User manual TRICITY CH550B

[. . . ] 5 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Do's and Don'ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Help Us To Help You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If not then draw these to the attention of the installer who should be a qualified electrician or a competent person. Tricity Bendix disclaims all liability for any damage or injury caused as a result of not following the instructions contained in the following text. ELECTRICAL CONNECTION Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood. WARNING: THIS APPLIANCE MUST BE EARTHED This appliance is fitted with a 3 core mains supply cable and should be permanently connected to the electricity supply via a double-pole switch having 3mm minimum contact gap on each pole. A Switched Fuse Connection Unit to BS. 1363 Part 4 (fitted with a 3A fuse), is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. CONNECTION TO THE MAINS POWER SUPPLY Any permanent electrical installation must comply with the latest I. E. E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). WARNING: INCORRECT INSTALLATION COULD AFFECT THE SAFETY OF THIS CHIMNEY HOOD. DISCONNECT THE HOOD FROM THE MAINS SUPPLY BEFORE CARRYING OUT ANY KIND OF MAINTENANCE OR CLEANING. This appliance conforms to BS. 800:1988 and EEC Directive 87/308 regarding suppression of radio and television interference. 4 INSTALLATION Unpacking Care should be taken when unpacking the cooker hood to ensure the fixing kit, ducting spigot and literature pack are retained with the hood. The fixing kit comprises of No 8 - 13mm fixing screws INSTALLATION Cont'd screw holes will require the removal of the metal grille panel. Press back on the two slide catch fasteners located on the front edge of the grille, which may then be pivoted down. Raise the hood into the cut-out and mark the position for the fixing screws. Pilot drill the fixing holes and fit the hood using the fixing screws supplied having ensured the ducting and mains supply cord have been connected. Positioning When installed above an electric cooking appliance the minimum distance between the surface of the hob elements and the lower grille of the cooker hood must be 65cm (25 1/2"). When installed above a gas cooking appliance the minimum distance between the surface of the hob pan supports and the lower grille of the cooker hood must be 70cm (27 1/2"). When installed above a cooking appliance with a high level grill the minimum distance between the upper surface of the grill and the lower grille of the cooker hood must be 45cm (17 3/4"). The distance between the underside of adjoining wall cabinets and the worktop must not be less than 40cm (15 3/4"). Care should be taken when unpacking the cooker hood to ensure that the fixing kit, ducting spigot and literature pack are retained with the hood. Recirculation The hood is supplied specified for installation in the extraction mode. To convert the hood to recirculation it will be necessary to obtain the (optional) charcoal filter. Charcoal filters can be obtained by using the order form enclosed. To fit the charcoal filter, open the metal inlet grille as illustrated in fig. [. . . ] it may be that the problem is a simple one, which you can solve yourself without the expense of a Service call. If our Service Engineer finds that the problem is listed below you will be charged for the call whether or not the appliance is under guarantee: - Make sure the appliance is properly wired in and that the Connection Unit is switched "ON". - Check there is power to the Connection Unit. - Check the fuse in the Connection Unit. [. . . ]