User manual TRICITY CH610W

[. . . ] Visor Cooker Hood - CH 520 and CH 610 Operating and Installation Instructions CONTENTS Please refer to the sections in this booklet that apply to your particular model: CONTENTS WARNINGS GENERAL INSTALLATION INSTRUCTIONS Page 1 2 3 4 5 5 5 6 6 7 7 8 8 9 ELECTRICAL CONNECTION UNPACKING POSITIONING WALL FITTING WALL CABINET FITTING DUCTING FITTING WORKTOP LIGHTING FILTERS OPERATING INSTRUCTIONS DO'S AND DON'TS MAINTENANCE AND CLEANING MAINTENANCE AND CLEANING HELP US TO HELP YOU TECHNICAL SPECIFICATIONS DIMENSIONS CH520 CH610 Width Width Height Depth Depth with visor open cm cm cm cm cm 49. 8 59. 8 15. 0 48. 0 53. 0 WEIGHT CH520 CH610 Gross Net Gross Net kg kg kg kg 8. 2 7. 2 8. 7 7. 7 ELECTRICAL CONNECTION Voltage Fan Lamps 2x40W Total Consumption 220-240V ~ 50Hz 110W 80 W 190W PERFORMANCE Speed Capacity m3/h Capacity lt/sec Pressure mmH 2O Noise level dbA 1 130 36 10 45 2 180 50 18 51 3 250 69 25 59 1 WARNINGS It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings. Please ensure that you have read the whole instruction book before using the appliance and that you follow the recommendations given. These warnings are provided in the interest of safety. [. . . ] When drilling the holes for the wall fixing brackets care must be taken to ensure that they are quite level as there is minimal vertical height adjustment of the fixing brackets. The brackets should be fitted with the round end at the bottom using the plastic rawl plugs and screws provided. If the brackets are to be fitted to a hollow plaster or partition board structure then the plastic rawl plugs provided should not be used. Once the brackets are secured lift the hood squarely to the wall slightly higher than the brackets and lower the cooker hood until the cooker hood locates onto the two brackets. Ensure that the cooker hood is correctly located before letting go. Access to the two wall levelling screws and the security fixing system will require the removal of the lower inlet grille that supports the grease mat filter. To remove the lower grille press inwardly on the two slide catches located towards either side of the grille near the front and the grille will open from the front. Slide the right edge of the grille forward until it clears the guide and then unhook the left hinge pin. Care should be taken to fully support the grille when removing it from the guides. The two wall levelling screws will be visible toward either end of the back panel, visible when the grille has been removed. Turn the screws clockwise to lift the front edge of the hood and use a spirit level to check the hood is positioned at right angles to the wall before fitting the security system. The wall brackets have two studs and when the cooker hood is hung onto the brackets the studs project through the two holes above the levelling screws. When the hood is level fit the two shakeproof washers and nuts supplied to fully secure the cooker hood. 4 POSITIONING When installed above an electric cooking appliance the minimum distance between the surface of the hob elements and the lower grille of the cooker hood must be 65cm (25 1/ 2"). When installed above a gas cooking appliance the minimum distance between the surface of the hob pan supports and the lower grille of the cooker hood must be 70cm (27 1/2"). However, if you are installing above a Tricity Bendix hob the minimum distance between the surface of the hob elements/ pan supports and the lower grille of the cooker hood may be reduced to 60cm (23 5/8") When installed above a cooking appliance with a high level grill the minimum distance between the upper surface of the grill and the lower grille of the cooker hood must be 45cm (17 3/ 4"). The distance between the underside of adjoining wall cabinets and the worktop must not be less than 40cm (15 3/4"). WALL FITTING The cooker hood may be fitted to any rigid vertical surface. All the fittings supplied are to be found in a polythene bag inside the carton. IMPORTANT: Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas pipes before drilling. If it is necessary to fix the hood to a hollow construction plaster or partition board structure then it must be sufficiently reinforced to be quite rigid in the area of the cooker hood mounting INSTALLATION Cont'd Before fitting the cooker hood beneath any type of wall cabinet ensure it is firmly fixed to the wall in accordance with the manufacturers instructions. Use the paper template provided to mark the hole positions on the underside of the cabinet. [. . . ] Do keep heating areas on your hob covered over with pots and pans when using the hob and cooker hood simultaneously. Don'ts Don't leave naked flames under the hood. Don't leave frying pans unattended during use as over heated fats and oils may catch fire. Don't do flambe cooking under this cooker hood. CHARCOAL FILTER The charcoal filter cannot be cleaned. [. . . ]