User manual TRICITY CPD91W

[. . . ] It is dangerous to alter the specifications or attempt to modify this product in any way. All packing and transit bolts must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person. [. . . ] Other letters and/or a bar beneath the circle will indicate the required process to the dry cleaner. May be tumble dried with high heat setting with low heat setting X A cross through any symbol means «DO NOT» Important Notes For best results, always use the dispenser drawer for dispensing detergents and liquid additives. Once the dispenser has been filled, close it by pushing it in gently. This is particularly important if you are using fabric conditioner to avoid the conditioner entering the machine prematurely. When using liquid detergent and a prewash programme, place the detergent into the correct compartment in the dispenser drawer, after the prewash has finished. 15 Washing Programmes Programmes for cotton and linen Wash programme Degree of soil and type Programme dial of laundry position White cotton, for example heavily soiled garments, sheets, household linen, underwear, towels. White cotton, for example normally soiled garments, sheets, household linen, underwear, towels. White cotton, for example lightly soiled garments, sheets, household linen, underwear, towels. Description Prewash at 40 °C Wash at 90°C 4 rinses Long spin at 800 rpm Possible options Max. load Pre-wash & Whites 1 HALF LOAD 4. 5 kg Whites 2 2+ ECO WASH Wash at 90°C 4 rinses Long spin at 800 rpm HALF LOAD 4. 5 kg Whites+ ECO WASH Wash at 60°C 4 rinses Long spin at 800 rpm HALF LOAD 4. 5 kg Fast coloured cotton or linen fabric, shirts, Fast Coloureds underwear, towels. (normally soiled) 3 (*) 3+ ECO WASH Wash at 60°C 4 rinses Long spin at 800 rpm Wash at 40°C 4 rinses Long spin at 800 rpm Wash at 40°C 4 rinses Long spin at 800 rpm 4 rinses Long spin at 800 rpm HALF LOAD 4. 5 kg Fast coloureds+ linen fabric, shirts, underwear, towels. ECO WASH (lightly soiled) Fast coloured cotton or HALF LOAD HALF LOAD HALF LOAD 4. 5 kg Non fast coloureds Hand Rinses Non fast coloured cotton or linen fabrics, shirts, blouses, underwear. Separate rinse cycle for hand washed garments. Clean carefully under a fast running tap. Replace the filter turning now clockwise and tighten it. P0201 P0198 Warning When the appliance is in use and depending on the programme selected there can be hot water in the filter. Never remove the filter during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the filter, ensure it is securely retightened so as to stop leaks and young children being able to remove it. P0212 P0040 The water inlet filters If your water is very hard or contains traces of lime deposit, the water inlet filters may become clogged. It is therefore a good idea to clean it from time to time. Remove and clean the filters using a hard bristle brush. Replace the filters and tighten up the inlet hoses. P0090 P0021 The dangers of freezing If the machine is exposed to temperatures below 0°C, certain precautions should be taken. s Unhook the drain hose from the rear support and position the end of this hose and that of the inlet hose in a bowl. s Screw the inlet hoses and reposition the drain hose. s When you intend to start the machine up again, make sure that the room temperature is above 0°C. Maintenance Wash With the use of low temperature washes it is possible to get a build up of residues inside the drum. We recommend that a maintenance wash be performed on a regular basis. [. . . ] Use the plastic "U-piece" supplied. P0022 28 Min. 60 cm. (23. 6") The appliance drain hose should hook (use the plastic "U-piece" supplied) into a standpipe with an internal diameter of approximately 38mm (see diagram) thus ensuring there is an air break between the drain hose and standpipe. Levelling Level the washing machine by loosening or tightening the feet. Once in the right position fix the feet by pushing the nuts against the base of the case. Accurate levelling prevents vibration, noise and displacement of the machine during operation. [. . . ]