User manual TRICITY DH041

[. . . ] Starting Required position of the push button programme selector Recommended quantity of detergent Wash Prewash Cycle description RINSE & HOLD 1 On/Off / / 1 cold rinse (to avoid food scraps from sticking together). Cold prewash Main wash up to 65°C 1 cold rinse 1 hot rinse Drying Main wash up to 65°C 1 cold rinse 1 hot rinse Drying Main wash up to 65°C 1 cold rinse 1 hot rinse * POWER WASH Normal soil Crockery and cutlery 2 On/Off 20 g 5g NORMAL WASH Light soil Crockery and cutlery 3 On/Off 25 g / ** ECO WASH Light soil Crockery, cutlery and party crockery 4 On/Off 25 g / * Testing programme for EN 50242 (see "Hints for Test Centres"). ** This is a special programme for quick washing a full load of lightly soiled dishes, glasses and crockery (except pots) so that you may re-use them promptly. 4 Operating sequence 1. Check the filters Ensure they are clean and properly positioned (see "Maintenance and cleaning" Instruction book Part 1). 9. At the end of the washing programme At the end of the programme the dishwasher will automatically stop. 2. Check that there is rinse aid and salt (See Instruction book - Part 1). 10. [. . . ] Check the filters Ensure they are clean and properly positioned (see "Maintenance and cleaning" Instruction book Part 1). 9. At the end of the washing programme At the end of the programme the dishwasher will automatically stop. 2. Check that there is rinse aid and salt (See Instruction book - Part 1). 10. Switch off the dishwasher Switch off the dishwasher by pressing the On/Off push button. Wait 15/20 minutes before opening the dishwasher's door; in this way you will avoid burning yourself when removing the dishes and avoid also the damage of the nearby furniture caused by the escape of steam. Empty the lower basket first and then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one. 3. Load the dishes Remove any scraps of food. Pull the lower basket out and arrange the saucepans, plates and cutlery in it. Pull the upper basket out and arrange the plates, saucers, glasses and cups etc. Slide the baskets back into the machine. 4. Ensure that the spray arms can rotate freely. Measure out detergent Add the required amount of detergent into the dispenser according to the "Washing programmes" chart. Light items (plastic bowls etc. ) should be loaded in the upper basket and arranged so they do not move. US07 Before closing the door, ensure that the spray arms can rotate freely. Adjusting the height of the upper basket If washing very large plates (over 27 cm and up to 31 cm in diameter) you can load them in the lower basket after moving the upper basket to the higher position. To move to the higher position proceed as follows: 1. Move the front runner stops (A) of the upper basket outwards and slide the basket out. Refit the basket in the higher position and replace the stops (A) in their original position. RC01 A When the top basket is in the higher position it will only take plates up to 20 cm in diameter and you will not be able to use the cup rack. After loading your machine always close the door, as an open door can be a hazard. 7 Hints for test centres Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse aid dispenser Test standard: Reference programme: Load: Rinse aid selector: Detergent dosage: EN 50242 NORMAL WASH 8 standard place settings position 4 20 g in the dispenser 5 g on the dispenser lid Arrangement upper basket Arrangement lower basket Arrangement cutlery basket Technical specifications Dimensions Width Height with worktop Height without worktop Max depth Max depth with open door Voltage 45 cm 85 cm 82 cm 61 cm 115. 9 cm 220/240 V - 50 Hz 200 W 2800 W 3000 W 50 kPa (0. 5 bar) 800 kPa (8 bar) 8 place settings 8 Electrical connection Motor rating during wash Power of heating element Overall power Water supply pressure Minimum Maximum Capacity Fitting under a counter (kitchen worktop or sink) By removing the machine's worktop, you can install it under a close fitting sink unit or a pre-existing top, providing the dimensions of the recess correspond to those shown in the picture. Proceed as follows: - Remove the machine's worktop by unscrewing the two front retaining screws, pull from the front and slide out the rear slots, lifting the worktop. Insert the machine after adjusting height and levelling with the adjustable feet. When inserting the machine, ensure that the water inlet and drain hoses are not kinked or squashed. 570- 600 450 IN04 Levelling Good levelling is essential for correct closure and sealing of the door. When the appliance is correctly levelled, the door will not catch on the levelling spacers on either side of the cabinet. [. . . ] Insert the machine after adjusting height and levelling with the adjustable feet. When inserting the machine, ensure that the water inlet and drain hoses are not kinked or squashed. 570- 600 450 IN04 Levelling Good levelling is essential for correct closure and sealing of the door. When the appliance is correctly levelled, the door will not catch on the levelling spacers on either side of the cabinet. [. . . ]