User manual TRICITY HG250B

[. . . ] Better Value. GAS HOB INSTRUCTION BOOKLET - INSTALLATION AND SERVICING INSTRUCTIONS MODEL NOS. HG 250 2 WARNINGS AND GUIDANCE It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings. These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. · This appliance is designed to be operated by adults, for non professional purpose in private houses only. [. . . ] * Products of Tricity Bendix manufacture which are NOT marketed by Tricity Bendix. * EU Countries - The standard guarantee is applicable but subject to owner's responsibility and cost to ensure the appliance meets the standards set by the country to which the product is taken. Electrolux Afersales Service in the country concerned, with whom Tricity Bendix have an agreement, will be pleased to advise further. 10 INSTRUCTIONS FOR THE INSTALLER - TECHNICAL DATA OVERALL DIMENSIONS Width: Depth: Thickness: Height: Weight: 580 mm. 11 Kg. CUT OUT DIMENSIONS Width: Depth: 550 mm. 470 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. This appliance complies with the EEC Directive No 89/336, concerning suppression of radio electrical interference. Ignition HT Spark Spark Generator Spark Gap Ispra Control's BF 50046 - 240V 0. 6 YA T 120 Fixed Rear Right Burner (semi rapid) Heat Input 1. 9 kW (6483 BTU/HR) Front Right Burner (auxiliary) Heat Input 1. 0 kW (3412 BTU/HR) Rear Left Burner (semi rapid) Heat Input 1. 9 kW (6483 BTU/HR) Front Left Burner (rapid) Heat Input 2. 9 kW Natural Gas (9895 BTU/HR) 2. 7 kW L. P. G. (9212 BTU/HR) CHARACTERISTICS TYPE OF GAS BURNER RAPID (large) MAX MIN SEMI-RAPID (medium) MAX MIN AUXILIARY (small) MAX MIN POSITION NOMINAL THERMAL POWER kW NOMINAL FLOW RATE m3/h NOZZLE REFERENCE 1/100 mm NOMINAL THERMAL POWER kW NOMINAL FLOW RATE VALUE = 37. 78 MJ/m3 Ws - 50. 7 MJ/ m3 NATURAL GAS 20 mbar 2. 9 0. 65 1. 9 0. 45 1. 0 0. 33 0. 276 119 0. 062 Adjust. 0. 181 96 0. 043 Adjust. 0. 095 70 0. 031 Adjust. VALUE = 49. 92 MJ/Kg LPG GAS 28-30/37 mbar 2. 7 0. 65 1. 9 0. 45 1. 0 0. 33 g/h 195 86 46. 8 40 137 71 32. 4 32 72 50 23. 8 28 NOZZLE REFERENCE 1/100 mm Burner Dia. Tap By-pass 1/100 mm 28 32 40 Tap colour Auxiliary Semi-rapid Rapid Red/Red Blue/Blue Black/Black Aeration adjustement none 11 INSTALLATION IMPORTANT It is essential that a competent installer is employed to fit this appliance. The manufacturer will not accept liability, should the above instruction or any of the other safety instructions incorporated in this book be ignored. On the end of the shaft, which includes the GJ 1/2" threaded nut, adjustment is fixed so that the washer is interposed between the components as shown in Figure 1. Screw the parts together without using excessive force, orientate the adjustment in the desired direction and then lock it all together. Connection to the gas supply should be with either rigid or semi-rigid pipe, i. e. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob. Rectangular cut-out size for hob 0 58 51 0 55 0 47 0 55 mi n. FO 2109 Fig. 1 A) End of shaft with nut B) Washer C) Adjustable join It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. 12 INSTALLATION ABOVE CUPBOARD OR DRAWER If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in illustrations A and B. 30 A ON/OFF SWITCH B ON/OFF SWITCH C a b 60 FLEX OUTLET FLEX OUTLET FO 0763 FO 0764 FO 1013 BUILDING IN KITCHEN UNIT WITH DOOR Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in inllustration C. [. . . ] Turn on the burner gas supply and ignite another burner supply. The pressure reading should be nominally 20mbar and must be between 17 mbar and 25mbar. Turn off the burner supplies. 19 SERVICING A: Removal Of Hob Top 1. Remove the panstands and each burner cap and crown. [. . . ]