User manual TRICITY RF561W

[. . . ] Partial load (to be completed later in the day). 1 On/Off / / 1 cold rinse (to avoid food scraps from sticking together). Cold prewash Main wash up to 65°C 1 cold rinse 1 hot rinse Drying Main wash up to 65°C 1 cold rinse 1 hot rinse Drying Main wash up to 65°C 1 cold rinse 1 hot rinse * POWER WASH 65° Heavy soil. Crockery, cutlery, pots and pans. 2 On/Off 25 g 5g NORMAL WASH 65° Normal soil Crockery and cutlery 3 On/Off 30 g / ** ECO WASH 65° Light soil Crockery cutlery 4 On/Off 30 g / * Testing programme for EN 50242 (see "Hints for Test Centres"). ** This is a special programme for quick washing a full load of lightly soiled dishes, glasses and crockery (except pots) so that you may re-use them promptly. Hints for test centres Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse aid dispenser Test standard: Reference programme: Load: Rinse aid selector: Detergent dosage: EN 50242 POWER WASH 65° 12 standard place settings position 5 25 g in the dispenser 5 g on the dispenser lid US57 UI67 Arrangement upper basket Arrangement lower basket 3 Operating sequence 1. [. . . ] Check the filters Ensure they are clean and properly positioned (see "Maintenance and cleaning"). 9. At the end of the washing programme At the end of the programme the dishwasher will automatically stop. The "Mains On" indicator light remains on until the On/Off push button is depressed. 2. Check that there is rinse aid and salt 3. Load the dishes Remove any scraps of food. Pull the lower basket out and arrange the saucepans, plates and cutlery in it. Pull the upper basket out and arrange the plates, saucers, glasses and cups etc. Slide the baskets back into the machine. 10. Switch off the dishwasher Switch off the dishwasher by pressing the On/Off push button. Mix spoons with other cutlery to prevent them from sticking together. Arrange spoons, dessert spoons, teaspoons, knives and other small items of cutlery in the rack on the side of the cutlery basket. UI27 UI66 5 The upper basket The upper basket is designed for plates (dessert plates, saucers, dinner plates of up to 24 cm in diameter), salad bowls, cups and glasses. If dishes are loaded in the upper basket, tilt them forwards. Arrange items on and underneath the fold-down cup racks so that water can reach all surfaces. Light items (plastic bowls etc. ) should be loaded in the upper basket and arranged so they do not move. Before closing the door, ensure that the spray arms can rotate freely. US64 US70 Adjusting the height of the upper basket If washing very large plates (over 27 cm and up to 31 cm in diameter) you can load them in the lower basket after moving the upper basket to the higher position. To move to the higher position proceed as follows: 1. Move the front runner stops (A) of the upper basket outwards and slide the basket out. Refit the basket in the higher position and replace the stops (A) in their original position. RC01 A When the top basket is in the higher position it will only take plates up to 20 cm in diameter and you will not be able to use the raised cup racks. After loading your machine always close the door, as an open door can be a hazard. 6 Adjusting the worktop You can move the worktop forward or backward by 25 mm in order to align the machine with other kitchen units. [. . . ] Refit the basket in the higher position and replace the stops (A) in their original position. RC01 A When the top basket is in the higher position it will only take plates up to 20 cm in diameter and you will not be able to use the raised cup racks. After loading your machine always close the door, as an open door can be a hazard. 6 Adjusting the worktop You can move the worktop forward or backward by 25 mm in order to align the machine with other kitchen units. Simply unscrew the two rear retaining screws, move the top to the required position and then retighten the screws. Fitting under a counter (kitchen worktop or sink) By removing the machine's worktop, you can install it under a close fitting sink unit or a pre-existing top, providing the dimensions of the recess correspond to those shown in the picture. Proceed as follows: Remove the machine's worktop by unscrewing the two rear retaining screws, pull from the front and slide out the rear slots, lifting the worktop. IN26 570 - 600 600 Insert the machine after adjusting height and levelling with the adjustable feet. [. . . ]