User manual TRICITY SI320W

[. . . ] · Any electrical installation must be carried out by a qualified electrician/competent person. · Remove all packaging before using the cooker. · This cooker must not be connected to a combustion products evacuation device. It shall be installed and connected in accordance with current installation regulations. [. . . ] · Release the knob and check that the burner has ignited. · Upon ignition, adjust the flame as required. If for any reason the flame should extinguish turn off the relevant control knob, leave for at least one minute and then re-ignite. If after a few attempts the burner does not ignite, check that the burner ring and its cap are correctly positioned. Turning off the burners Turn the control knob clockwise to mark « ». Do not put anything on the hob that is liable to melt. Good use Selecting the Correct burner Above every knob there is a symbol for the corresponding burner. For good cooking results, always choose pans, which correctly fit to the diameter of the burner used (see figs). We recommend the flame is lowered as soon as the liquid starts boiling. To prevent discolouration, regularly wipe away condensation and also soilage from surfaces. Cookware Use any ovenproof cookware, withstand temperatures of 250°C. which will · The thickness, the material and the colour of the pan will influence the cooking results. · When cooking, certain dishes increase in volume, ensure the pan is large enough. Cleaning the oven door For a more complete cleaning of the oven door, it is advisable to remove it in the following way; Open the door completely. Lift the two locking plates on the hinge arms to 170°; Partially close the door, to a 30o angle Lift the door and pull out. locking plates · · · · · · Oven Cavity The enamelled oven cavity is best cleaned whilst the oven is still warm. Wipe the oven over with a soft cloth soaked in warm soapy water after each use. From time to time it will be necessary to do a more thorough cleaning, using a proprietary oven cleaner. Refit the door by described above. reversing the operation 13 DO NOT clean the oven door while the glass panels are warm. If this precaution is not observed the glass panel may shatter. If the door glass panel becomes chipped or has deep scratches, the glass will be weakened and must be replaced to prevent the possibility of the panel shattering. Contact your local Service Centre who will be pleased to advise further. OVEN BULB REPLACEMENT Ensure that the appliance is switched off and disconnected from the electricity supply before replacing the bulb to avoid possibility of an electric shock. If the oven bulb needs replacing, it must comply with the following specifications: Wattage: Voltage: Temperatures: Thread Type: 25W 230/240V(50Hz) 300ºC E14 To replace the faulty bulb. Turn the glass cover anticlockwise and remove. Remove the faulty bulb by turning it anticlockwise and replace with a new one. Reconnect the appliance to the electricity supply. 14 SOMETHING NOT WORKING If the appliance is not working correctly, please carry out the following checks, before contacting your local Service Force Centre. [. . . ] SPECIFICATION NOZZLES Table no. 1 (Cat : II 2H3+) Burner Normal power (kW) Simmer power (kW) Bypass (mm) Gas Type Natural Gas Butane Propane Natural Gas Butane Propane Natural Gas Butane Propane Natural Gas Butane Propane Natural Gas Butane Propane Pressure (mbar) 20 28-30 Nozzle diameter (mm) Cons m3/h 0, 267 0, 190 0, 095 0, 267 0, 190 g/h 218, 1 214, 2 145, 4 142, 8 72, 7 71, 4 218, 1 214, 2 145, 4 142, 8 RAPID SEMIRAPID AUXILIARY 3, 00 0, 72 0, 42 37 20 28-30 2, 00 0, 43 0, 32 37 20 28-30 1, 00 0, 35 0, 29 37 20 28-30 OVEN 3, 00 1, 10 0, 46 37 20 28-30 GRILL 2, 00 - - 37 1. 19 0, 88 0, 88 0. 96 0, 71 0, 71 0. 70 0, 50 0, 50 1. 16 0, 87 0, 87 0, 96 0, 71 0, 71 24 Replace the nozzles of the hob burners Before any modifications or conversion to a kind of different gas, you must DISCONNECT the cooker from the electricity supply and ensure that all control knobs are in the OFF position, and the appliance has cooled completely. Hob burners · · · Remove the pan supports; Remove the caps and the burner crowns; Using a No 7 socket spanner unscrew the nozzles and replace them with those required for the type of gas in use (see table no. Reassemble the parts following the same procedure in reverse. These burners do not need any primary air regulation. Adjustment of minimum level for the hob burners The burner is correctly adjusted when the flame is stable silent and goes out without any noise. [. . . ]