User manual TRICITY TBG640BL

[. . . ] Ensure that the gas and electrical supply complies with the type stated on the rating plate, located near the gas supply pipe. Do not attempt to modify the hob in any way. This hob should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. Environmental Information After installation, please dispose of the packaging with due regard to safety and the environment. When disposing of an old appliance, make it unusable, by cutting off the cable. Keep this instruction book for future reference and ensure it is passed on to any new owner. Child Safety This hob is designed to be operated by adults. [. . . ] For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk Before calling out an engineer, please ensure you have read the details under the heading "Something Not Working. " When you contact the Service Force Centre you will need to give the following details: 1. Clear and concise details of the fault 4. The model and serial number of the appliance (found on the rating plate) 5. The purchase date 5 Customer Care Department For general enquiries concerning your appliance, contact our Customer Care Department by letter or telephone as follows: Major Appliances Customer Care Tricity Bendix Major Appliances Addington Way Luton Bedfordshire LU4 9QQ Tel: 08705-950950* * calls to this number may be recorded for training purposes Guarantee Conditions Tricity Bendix Standard Guarantee Conditions We, Tricity Bendix, undertake that if, within 12 months of the date of the purchase, this Tricity Bendix appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: * The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate. * The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's instructions. * The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. * All service work under this guarantee must be undertaken by a Tricity Bendix Service Force Centre. * Any appliance or defective part replaced shall become the Company's property. * This guarantee is in addition to your statutory and other legal rights. Home visits are made between 8. 30am and 5. 30pm Monday to Friday. Visit may be available outside these hours, in which case a premium will be charged. It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. FO 0814 FO 0264 A)End of shaft with nut B)Washer C)Elbow Rectangular cut-out size for hob 470 Cut Out Size The dimensions of the cut-out are given in the diagram. 30 550 Dimensions are given in mm. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2. FO 2098 1 ON/OFF SWITCH FLEX OUTLET Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. ON/OFF SWITCH FO 0763 2 30 3 60 a b FLEX OUTLET FO 0764 FO 1013 Dimensions are given in mm. 20 min 9 Fitting the Hob into the worktop Carry out the building in of the hob as follows: · put the seals supplied with the hob, on the edges of the cut out, taking care that the seals meet without overlapping; · place the hob in the cut out, taking care that it is centred; · fix the hob with the relevant fixing clamps and screws, as shown in the diagram. When the screws have been tightened, the excess seal can be removed. FO 0199 a a) Sealing gasket The edge of the hob forms a double seal which prevents the ingress of liquids. 10 Electrical Connections THIS HOB MUST BE EARTHED. Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. Upon completion there must be no cut, or stray strands of wire present and the cable clamp must be secure over the outer sheath. A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut off plug is disposed of safely. Electrical Requirements Any permanent electrical installation must comply with the latest I. E. E. [. . . ] IGNITOR UNIT B N Fault finding Preliminary Electrical Systems Check Brown Blue Green Yellow PLUG (with cover removed) Earth Wire Green/Yellow SOCKET (face view) () FUSE E( ) START Isolate appliance and carry out: A: Earth Continuity check. Neutral Wire Blue N L Blue Brown Green Yellow NO YES Carry out: C: Polarity check. Carry out: D: Resistance to Earth check. Electricity supply should now be satisfactory. Has inlet fuse blown? NO YES A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on (Ohms) x 1 scale and adjust zero if necessary. a) Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0. 1 (Ohm), check all earth wires for continuity and all contacts are clean and tight. Inlet wiring faulty. [. . . ]