User manual TRICITY TBG640BR

[. . . ] Remove all packaging before using the hob. Ensure that the gas and electrical supply complies with the type stated on the rating plate, located near the gas supply pipe. This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. [. . . ] Keep these components very clean, to avoid lighting difficulties, and check that the burner crown holes are not obstructed. 5 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMPTOM # There is no spark when lighting the gas SOLUTION $ Check that the unit is plugged in and the electrical supply is switched on $ Check that the RCCB has not tripped (if fitted) $ Check the mains fuse has not blown $ Check the burner cap and crown have been replaced correctly, e. g. after cleaning. # The gas ring burns unevenly $ Check the main jet is not blocked and the burner crown is clear of food particles. $ Check the burner cap and crown have been replaced correctly, e. g. after cleaning. If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Electrolux Service Force Centre by telephoning: 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk Before calling out an engineer, please ensure you have read the details under the heading "Something Not Working. " When you contact the Service Force Centre you will need to give the following details: 1. Clear and concise details of the fault 4. The model and serial number of the appliance (found on the rating plate) 5. The purchase date 6 Customer Care Department For general enquiries concerning your Tricity Bendix appliance or for further information on Tricity Bendix products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www. tricity-bendix. co. uk For Customer Service in the Republic of Ireland please contact us at the address below: Tricity Bendix Electrolux Group (Ire) Ltd. Long Mile Road Dublin 12 Republic of Ireland Tel: + 353 (0) 1 4090751 e-mail: service. eid@electrolux. ie Customer Care Department Major Appliances Tricity Bendix Addington Way Luton Bedfordshire LU4 9QQ Tel: 08705-950950* * calls to this number may be recorded for training purposes Guarantee Conditions Tricity Bendix Standard Guarantee Conditions We, Tricity Bendix, undertake that if, within 12 months of the date of the purchase, this Tricity Bendix appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: * The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate. * The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's instructions. 813 Current Editions Table Four. FO 0812 FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 600 mm 650 mm 400 mm Location The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom, shower room or garage. Before making the cut out in the worktop ensure that the edges of the hob that are to be near either a side or rear wall have a minimum distance of 55 mm between the edge of the hob and the wall. A minimum distance of 100 mm must be left between the side edges of the hob and any adjacent cabinets or walls. The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 400 mm. If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob. The minimum distance combustible material can be fitted directly above the hob is 700 mm. For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I. S 813 Current Edition Section 7- Permitted Locations of Appliance. 50 m 55 m mm 400 mm 100 mm 50 m m FO 0813 9 Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i. e. [. . . ] A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut off plug is disposed of safely. FO 0390 12 Wiring diagram L 1 A 0 2 3 220/240 4 A. IGNITOR UNIT B N Fault finding Preliminary Electrical Systems Check Brown Blue Green Yellow PLUG (with cover removed) Earth Wire Green/Yellow SOCKET (face view) () FUSE E( ) START Isolate appliance and carry out: A: Earth Continuity check. Neutral Wire Blue N L Blue Brown Green Yellow NO YES Carry out: C: Polarity check. Carry out: D: Resistance to Earth check. Electricity supply should now be satisfactory. Has inlet fuse blown? NO YES A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on (Ohms) x 1 scale and adjust zero if necessary. [. . . ]