User manual TRIMBLE 5800 RELEASE NOTES 4.19 REV A

[. . . ] Registration To receive information regarding updates and new products, please contact your local dealer or visit the Trimble website at lwww. trimble. com/register. Upon registration you may select the newsletter, upgrade or new product information you desire. Notices Class B Statement ­ Notice to Users. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. [. . . ] Warranties are available through your Trimble dealer. Note ­ Before you update to version 4. 19 on a Trimble R7 GNSS receiver, you must have firmware version 3. 60 or later installed. You cannot update to version 4. 19 directly from version 3. 50 or earlier--you must first download and install version 3. 64 from www. trimble. com and then install version 4. 19. · · · 12. 1 Canopy related RTK engine enhancements Russia geofence India geofence 12. 2 Trimble R7/R8/5700/5800 GPS receivers version 2. 32 · Added support for receivers that transmit (0. 00 m) antenna heights in CMR records Improved handling of satellite health messages Improved handling of RTCM 2. 1, 2. 2, 2. 3 & 2. x "New Base" detection · · 12. 3 Trimble R8 / 5800 GPS receivers (only) version 2. 31 Improvements to memory usage when overwriting large deleted files. 12. 4 Trimble R7/R8/5700/5800 GPS receivers version 2. 30 Several enhancements, including improvements to Bluetooth connections to a receiver using a GSM/GPRS modem. 4 Trimble R/5000 Series Receivers Release Notes 12. 5 Trimble R7/R8/5700/5800 GPS receivers version 2. 28 Improvements to Bluetooth connection during GSM / GPRS operation. 12. 6 Trimble R7/R8/5700/5800 GPS receivers version 2. 27 Improvements to: · · Bluetooth connection Internal frequency issue on the Trimble R7 / 5700 receivers 12. 7 Trimble R8 GNSS and R7 GNSS, and Trimble R6/5700 II/5800 II GPS receivers version 4. 12 · · · Enhancements relating to satellite tracking. Enhancements relating to VRS-RTK surveying. AutoBase is now available through the Web user interface. 12. 8 Trimble R8 GNSS and R7 GNSS, and Trimble R6/5700 II/5800 II GPS receivers version 4. 11 · RTK engine enhancements for operating in VRS networks with non-Trimble base stations The RTK engine now accommodates the latest generation GLONASS satellites L5 tracking enhancements You can now access the R8 GNSS and R7 GNSS Web user interface using PPP through a 7-pin lemo serial cable Trimble R4 and R6-2 antenna models are now supported Compliance has been improved for Bluetooth® wireless technology The R8 III clock rate has been adjusted at cold temperatures (below -20 °C) to enhance tracking capabilities Trimble R/5000 Series Receivers Release Notes 5 · · · · · · 12. 9 Trimble R8 GNSS and R7 GNSS, and Trimble R6/5700 II/5800 II GPS receivers version 4. 01 · Before you update a Trimble R7 GNSS receiver to version 4. 01, the receiver must have firmware version 3. 60 or later installed. ­ You cannot update to version 4. 01 directly from version 3. 50 or earlier--you must first download and install version 3. 64 ( from www. trimble. com) and then install version 4. 01. · The receiver file system (T01 storage) is updated to prepare for future improvements. Added dual-logging capability to the Trimble R7 GNSS and 5700 II receivers. ­ · You can now use the GPS Configurator application version 3. 71 or later for dual-logging in these receivers. · Added support for 20 Hz logging in Trimble R7 GNSS and 5700 II receivers. ­ You can now use the GPS Configurator application version 3. 71 or later for 20 Hz logging in these receivers. · Improved performance of pole-wobble detection. ­ Better triggering of "Excessive Pole Movement" messages. · Added support for Leica base receivers ­ This was removed in version 3. 64 and has now been restored. Internet base: Connect the receiver directly to the server ­ · IP Stack support in the receiver Using the Trimble Survey ControllerTM software, you can now configure an Internet base so that the receiver uploads directly to a distribution server; you do not have to leave the controller connected to the base receiver while the base survey is running. To do this, clear the Route through controller check box in the base dial profile. This feature enables you to start the Internet base 6 Trimble R/5000 Series Receivers Release Notes with a cable or with Bluetooth wireless communication, instead of with a Bluetooth connection only. You can upload base data directly to a specified server IP address and port number, or upload to an NTRIP server using a specified mountpoint (and password, if required). This feature requires receiver firmware version 3. 70 or later. The cable carries power only and must not be used in any other manner. Damage to equipment can occur if this cable is not used in conjunction with the Trimble R8 GNSS, Trimble R7 GNSS, and Trimble R6 GPS receivers and the Multi Battery Adaptor. 10 Trimble R/5000 Series Receivers Release Notes 1. 3 Registering the receiver Trimble recommends that you register your Trimble receiver to protect your investment and to ensure that the system is always up to date. If you register the receiver, you will be notified by e-mail when there are updates to the receiver firmware, or when new functionality becomes available. From the main menu, select Register your receiver. Do one of the following: ­ To register online, select Register using the Internet. The online registration form opens in your default web browser. Fill in the required fields, and then click Submit to submit the completed form. To register by mail, select Register using mail. The registration form opens in the Microsoft WordPad editor. Fill in the required fields, print the form, and then mail it to the address shown at the bottom of the form. ­ Trimble R/5000 Series Receivers Release Notes 11 1. 1 Updating the system files Before you can use your receiver with Trimble office software, such as Trimble GeomaticsTM Office, Trimble Total ControlTM, Terramodel®, or Trimble Business Center, you must install or update the following files: · The receiver Device Driver for Data Transfer You must have this file to transfer files from the CompactFlash card or the receiver internal memory to the computer, using the USB and serial ports or a Bluetooth wireless connection. · Configuration files These files provide the latest list of antennas and receivers that are recognized by Trimble software. They also ensure that antenna and receiver information flows correctly from the receiver to the Trimble Survey Controller software and to the office software. To install or update these files: 1. [. . . ] Follow the instructions in the installation wizard. 14 Trimble R/5000 Series Receivers Release Notes 10. 1 The Trimble Data Transfer utility Use the Trimble Data Transfer utility to transfer data between a variety of data collection devices and an office computer. Installing the Data Transfer utility Note ­ You can install the Data Transfer utility on any number of computers. To install the Data Transfer utility on another office computer, or to reinstall it without installing other software: 1. From the main menu, select Install individual software packages. [. . . ]