User manual TRIMBLE EZ-GUIDE 500 LIGHTBAR GUIDANCE SYSTEM FIRMWARE 4.05 RELEASE NOTES REV A

[. . . ] RELEASE NOTES EZ-Guide® 500 Lightbar Guidance System Firmware Version 4. 05 Introduction New features and changes Updates Resolved issues Upgrade procedure Version 4. 05 Revision A May 2009 Part Number 66022-84-ENG *66022-84-ENG* Contact information trimble_support@trimble. com www. EZ-Guide. com Legal Notices Copyright and Trademarks © 2007­2009, Trimble Navigation Limited. Trimble, the Globe & Triangle logo, AgGPS, EZ-Boom, EZ-Guide, and Tru Count are trademarks of Trimble Navigation Limited, registered in the United States and in other countries. Autopilot and VRS are trademarks of Trimble Navigation Limited. All other trademarks are the property of their respective owners. [. . . ] If the CPIN is enabled, then you must enter it correctly for your cellular modem to work. Note ­ If you enter the CPIN incorrectly 3 times in a row the SIM card is disabled and you will need to contact your cellular network provider. To keep the CPIN secure, the CPIN is not displayed on the EZ-Guide 500 system once it has been entered. When you are done, press . 8 EZ-Guide 500 Lightbar Guidance System Release Notes The VRS Server Setup Screen appears: 7. Use the virtual keyboard to enter the following information: Note ­ This information is supplied to you by the network administrator. Contact your network administrator for assistance. ­ server address: ­ port number: EZ-Guide 500 Lightbar Guidance System Release Notes 9 ­ mount point: Note ­ The mount point is case sensitive. Make sure you use the correct capitalization when entering this value. ­ user name and password Note ­ The user name and password are case sensitive. Make sure you use the correct capitalization when entering these values. The system attempts to connect to the Ag3000 modem, which then connects to the network. Verify the information you have entered on the VRS Status screen: When the Connection status shows 'Logged in', a successful connection has been made and you should be receiving RTK positions. Press to complete the wizard. 10 EZ-Guide 500 Lightbar Guidance System Release Notes Viewing VRS connection status information The main map screen shows the status of the VRS connection: The field. . . the number generated when you first connect to the correction source. For a VRS connection, this field shows a new number when a new connection is made. the age of the correction ­ that is, how long ago the correction was received. Logged In to indicate a successful connection to the VRS server, which indicates that you should be receiving corrections. Bars indicate cell signal strength. CMR age VRS Secure RTK The EZ-Guide 500 Lightbar Guidance System now supports Secure RTK. Secure RTK is an encryption service that can be applied to a base station network. This gives the network provider the ability to control which users can access the network and for how long. LB25 external lightbar support You can use the LB25 external lightbar as a remote lightbar for the EZ-Guide 500 Lightbar Guidance System. This allows a second lightbar to be mounted separately to the lightbar display itself. This is useful if the lightbar display is mounted to the side of the cab for ease of operation, as the external lightbar can be mounted on the windshield EZ-Guide 500 Lightbar Guidance System Release Notes 11 for an easy line-of-sight indication of vehicle position. The remote lightbar can also be mounted on the rear window for indication of vehicle position when observing the implement. Note ­ Only one external lightbar can be connected at any time. To connect an LB25 external lightbar to the EZ-Guide system, refer to the installation manual for the LB25 external lightbar. [. . . ] Delete the field data from the internal memory. Install the language packs and then, if necessary, use the drive to replace the field data in the lightbar's internal memory. A number of language packs are available as a web release. Language packs are loaded onto the lightbar from a USB drive: 1. Transfer the required language pack (. lpf file) from www. ez-guide. com to an office computer. [. . . ]