User manual TRIMBLE TERRASYNC 2.31 RELEASE NOTES REV A

[. . . ] TerraSyncTM Release Notes Introduction What's New?Product Information Installation on a CE Device Cabling Documentation Additions Known Problems Technical Assistance L ® Version 2. 31 Revision A May 2003 Corporate Office Trimble Navigation Limited Mapping & GIS 645 North Mary Avenue Post Office Box 3642 Sunnyvale, CA 94085 U. S. A. Warranty Exclusions and Disclaimer These warranties shall be applied only in the event and to the extent that (i) the Products and Software are properly and correctly installed, configured, interfaced, maintained, stored, and operated in accordance with Trimble's relevant operator's manual and specifications, and; (ii) the Products and Software are not modified or misused. The preceding warranties shall not apply to, and Trimble shall not be responsible for defects or performance problems resulting from (i) the combination or utilization of the Product or Software with hardware or software products, information, data, systems, interfacing or devices not made, supplied or specified by Trimble; (ii) the operation of the Product or Software under any specification other than, or in addition to, Trimble's standard specifications for its products; (iii) the unauthorized modification or use of the Product or Software; (iv) damage caused by accident, lightning or other electrical discharge, fresh or salt water immersion or spray; or (v) normal wear and tear on consumable parts (e. g. , batteries). Trimble does not warrant or guarantee the results obtained through the use of the Product. [. . . ] You will need to enter the TerraSync version 2. 30 serial number and authorization key, which are displayed on the CD case. If the message "Trimble TerraSync" is already installed. Do you want to proceed with the re-install/upgrade?appears, click Yes. 8. TerraSync Release Notes 15 9. When the message Install "Trimble TerraSync" using the default application install directory?appears, do one of the following: ­ Click Yes to install the software to the default location. TerraSync will be installed in the main memory of the CE device. Use this option if you are installing onto: · · · ­ a Trimble Recon handheld a CE device that has no secondary storage a CE device that only has removable secondary storage such as a CompactFlash card Click No to install the software to an internal secondary storage location. Use this option if you are installing onto: · · · · · a GeoExplorer CE handheld a GIS TSCe field device a TDS Ranger a Juniper Systems Allegro any other CE device that has an internal secondary storage location B Tip ­ Trimble recommends that you install to a secondary storage location to free up storage and program memory on the CE device. 16 TerraSync Release Notes 10. Do one of the following: ­ ­ If you clicked Yes in Step 9, go to Step 11. If you clicked No in Step 9, the Select Destination Media dialog appears. From the Save In list, select Disk, then click OK to proceed with the installation. 11. Respond to any messages that appear: ­ If a message appears on the CE device stating that TerraSync is already installed, and asking if you want to reinstall TerraSync, tap Yes. If the message Confirm ignore missing file appears on the CE device, tap Yes to All. If the message Install "Trimble TerraSync" to \Disk\Trimble TerraSync\ ?appears on the CE device, tap OK. ­ ­ 12. When the installation procedure is complete, perform a soft reset on the CE device. Note ­ When you install TerraSync on a GeoExplorer CE handheld, some settings are stored in the main memory (RAM), even though TerraSync is always installed to the Disk. To avoid data loss, the installation program automatically backs up the main memory immediately after installing TerraSync. TerraSync Release Notes 17 Installing a translation of TerraSync on a CE device 1. 4. 2 The TerraSync software is available in several languages. Language files for translated installations are not supplied on the TerraSync Software & Operation Guide CD; they must be downloaded from the Trimble website. The TerraSync setup program uses the TerraSync Updater utility to automatically download and install language files. Trimble recommends that you only install a TerraSync translation on a CE device that has the corresponding language version of the operating system installed. For example, install Japanese TerraSync on a CE device that has Japanese Windows CE installed. [. . . ] To establish a dial-up connection with a VRS provider using some cellphones (such as some Nokia models), you may need to send AT commands from the field computer to put the cellphone into ISDN mode. To configure the cellphone, connect it to a computer that is running a desktop Windows operating system. Some cellphones do not disconnect the dial-up connection to a VRS server when TerraSync sends a disconnect command. To ensure that a dial-up connection is ended, disconnect from the VRS server in TerraSync, and then end the call on the cellphone as well. · · · Restoring fonts · 1. 7. 4 After you perform a hard reset on a CE device that has a RAM backup feature (for example, a GeoExplorer CE handheld or a GIS TSCe field device), fonts that you have installed may not be available. [. . . ]