User manual TRIMBLE TERRASYNC 2.41 RELEASE NOTES REV B

[. . . ] TerraSyncTM Release Notes Introduction What's New?Product Information Registering TerraSync Installation on a CE Device Installation on a PC Cabling Known Problems Technical Assistance L ® Version 2. 41 Part number 43161-24-ENG Revision B July 2004 Corporate Office Trimble Navigation Limited Mapping & GIS Business Area 7403 Church Ranch Blvd, Suite 100, Westminster, CO 80021 Warranty Exclusions and Disclaimer These warranties shall be applied only in the event and to the extent that (i) the Products and Software are properly and correctly installed, configured, interfaced, maintained, stored, and operated in accordance with Trimble's relevant operator's manual and specifications, and; (ii) the Products and Software are not modified or misused. The preceding warranties shall not apply to, and Trimble shall not be responsible for defects or performance problems resulting from (i) the combination or utilization of the Product or Software with hardware or software products, information, data, systems, interfacing or devices not made, supplied or specified by Trimble; (ii) the operation of the Product or Software under any specification other than, or in addition to, Trimble's standard specifications for its products; (iii) the unauthorized modification or use of the Product or Software; (iv) damage caused by accident, lightning or other electrical discharge, fresh or salt water immersion or spray; or (v) normal wear and tear on consumable parts (e. g. , batteries). Trimble does not warrant or guarantee the results obtained through the use of the Product. [. . . ] From the Save In list, select Disk, then click OK to proceed with the installation. 14. Respond to any messages that appear: ­ If a message appears on the CE device stating that TerraSync is already installed, and asking if you want to reinstall TerraSync, tap Yes. If the message Confirm ignore missing file appears on the CE device, tap Yes to All. If the message Install "Trimble TerraSync" to \Disk\Trimble TerraSync\ ?appears on the CE device, tap OK. ­ ­ Note ­ On some CE devices, such as the Trimble Recon handheld, the message Adding information for "Remove Programs" may remain on the screen for several minutes. While this message is displayed, do not cancel the installation or reset the CE device. When the installation procedure is complete, perform a soft reset on the CE device. Note ­ When you install TerraSync on a GeoExplorer CE series handheld, some settings are stored in the main memory (RAM), even though TerraSync is always installed to the Disk. To avoid data loss, the installation program automatically backs up the main memory immediately after installing TerraSync. 18 TerraSync Release Notes Installing a translation of TerraSync on a CE device 1. 5. 2 The TerraSync software is available in several languages. Language files for translated installations are not supplied on the TerraSync Software & Operation Guide CD; they must be downloaded from the Trimble website. The TerraSync setup program uses the TerraSync Updater utility to automatically download and install language files. Trimble recommends that you only install a TerraSync translation on a CE device that has the corresponding language version of the operating system installed. For example, install Japanese TerraSync on a CE device that has Japanese Windows CE installed. System commands (such as the OK and Cancel buttons) are generated by the operating system, so they appear in the language of the operating system on the CE device. If you use TerraSync on a CE device that does not have the corresponding translation of the operating system installed, system commands are not translated. Also, some characters may not be interpreted or displayed correctly. For best results, make sure that the TerraSync and operating system languages match. If they do not, install any font that is supplied with TerraSync for that language. For more information, see Installing fonts on a CE device, page 21. B Tip ­ If you see squares or unusual characters instead of characters from the appropriate language, you need to install a font. Note ­ The Regional Options applet in the Control Panel only changes the display of date, time, units, and currency information. It does not change the language of the field computer's operating system. TerraSync Release Notes 19 To install a translation of TerraSync on a CE device: 1. Install the English version of TerraSync (see page 13). Use the TerraSync Updater utility to download and install the appropriate language file. [. . . ] If you have problems connecting TerraSync to the receiver, use the GPS Configurator software to check that the baud rate of the receiver port is set to 38400. GPS Configurator is supplied with the GPS receiver. TerraSync cannot turn off a 5700 or 5800 receiver. To turn off the receiver, use the Power button p on the receiver. · GeoExplorer CE series handheld · 1. 8. 7 If a GeoExplorer CE series handheld loses power, or you perform a hard reset, the main memory is cleared. [. . . ]