User manual TRUMA MOVER SE

[. . . ] Mover SE Mover TE Version UK Operating instructions Installation instructions To be kept in the vehicle! Page 3 Page 7 Sales and Service in UK and Eire: Truma (UK) Limited 2000 Park Lane, Dove Valley Park Foston South Derbyshire DE65 5BG telephone: (01283) 58 60 20 telefax: (01283) 58 60 29 sales@trumauk. com www. trumauk. com Mover SE Mover TE Version UK Installation example 1 2 3 4 5 6 Remote handset Drive motor Drive roller Electronic control unit Battery Safety socket Operating instructions Safety-related instructions l Practice operating the Mover in an open area before using for the first time. This to fully familiarise yourself with the handset/mover operation. l Always check tyres and drive rollers before using the equipment; remove sharp-edged stones and the like if necessary. l No person must be present in the caravan during operation. [. . . ] In other countries, respective service partners are available (refer to address list). In addition, the correctly completed warranty certificate must be presented or the Serial number of the appliance and the date of purchase specified. In order to allow the manufacturer to check whether it is a warranty case, the end consumer must take or send the device to the manufacturer at his own risk. In instances of the device being sent to the works, dispatch is to be effected by freight transport. In cases under warranty, the works shall bear the transport costs or the costs of delivery and return. If the damage is deemed not to be a warranty case, the manufacturer shall notify the customer and shall specify repair costs which shall not be borne by the manufacturer; in this case, the customer shall also bear the shipping costs. 2. Press the reset button (k) on the control unit and hold down (red LED ­ j ­ flashes slowly), and after approx. 5 seconds the LED (j) starts to flash rapidly. Then release the reset button and press and hold down the caravan reverse button on the remote hand set (c) within 10 seconds, simultaneously switching on the remote hand set using the slide switch (a). The remote hand set and the control unit are synchronised to each other. After successful synchronisation, the red LED flashes rapidly. 6 Installation instructions Read the installation instructions prior to starting work and follow them carefully!Please ensure that no metal chips or other contaminants get into the controller during installation. A distinction is made between L-profiled and U-profiled chassis as shown in the illustration. Caravan Floor L-Profile U-Profile Intended use The Mover SE is designed for use on single-axle caravans with a gross weight of up to 1800 kg, and the Mover TE is designed for use on dual-axle caravans with a gross weight of up to 2250 kg. Check the towing load of your vehicle and the gross weight of your caravan in order to establish whether they are designed for the additional weight. Measuring the chassis height Frame height (Y) measured at distance of 106 mm (X) from the outer edge of the tyre at height of hub/middle of tyre. Y Approval X The Truma-Mover SE/TE has design approval, and a general operating permit (ABE) has been issued for Germany. Acceptance by a vehicle expert is not required (except when installing the flat frame kit). The ABE can be requested from Truma and must be carried in the vehicle in Germany. The Mover SE/TE complies with the vehicle engine interference suppression directive 72/245/EEC with supplements 2004/104/EC and 2005/83/EC and bears type approval number: e1 03 4473. The Mover SE/TE complies with EMC directive 89/336/EEC. The remote hand set and the receiver comply with the requirements of the R&TTE directive 1995/5/EC. The technical and administrative regulations of the country in which the vehicle is initially registered must be complied with when the Mover is being installed. Any modification to the unit, or the use of spare parts and functionally-important accessories which are not original Truma components, or failure to respect the installation and operating instructions, will lead to the cancellation of the guarantee and to exclusion of claims for liability. in addition to this, the operational approval for the device will be cancelled. Determining the installation type 1. [. . . ] If LED does not illuminate, check polarity and condition of batteries in remote hand set. The remote hand set switches itself off after about 2 minutes if no buttons are pressed. Check whether both drive motors are stationary. Press the , , forwards" button with the remote hand set switched on ­ both drive motors must now move in the forward direction. [. . . ]