User manual TYAN NETSCALIBUR

[. . . ] Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 What is the Netscalibur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Inside the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] An interrupt or IO address conflict will prevent the driver from loading. You can access the Device Manager by moving the mouse cursor to My Computer follow by clicking on the right mouse button to bring out the properties sheet. Afterwards, click on properties to go to System Properties and then select Device Manager folder. Go down to network adapters and double-click on Netscalibur ISDN ISA-PnP to check Resources for conflicts. For Windows NT users, you should bring up the Windows NT diagnostic in Administrative tools to check for resource conflicts. The red lights may also be caused by a bad cable or cable connection. Check the ISDN RJ-45 to the phone jack and make sure they are properly inserted. L1 lights turn green but L2 and L3 remain red: This is normal if the phone company uses Point-to-Point protocol. The light will turn green once the connection has been established. Otherwise, it means that the driver is loaded but the switch type, SPID numbers, or the phone numbers for ISDN are incorrect. First check the switch type, SPID numbers, and phone numbers in the Start -> Programs -> Accessories -> ISDN tools -> ISDN Configuration Wizard. Make sure you enter the correct SPID numbers, phone numbers, and switch type. This information is supplied by the phone company. If you do not know the switch type, please select AUTO instead. The B Channel Activity light will turn green only after the connection has been established. If Ch1 turns green but Ch2 remains red, it means that only channel 1 is connected. The ISDN diagnostic tool does not work under Windows NT 3. 51. It will work under Windows 95 and Windows 4. 0. 7 95 1. Power off the system and insert the Netscalibur into an empty 16-bit ISA slot and remove other modem cards from the system. Afterwards, power on the system and boot to Windows 95. You must install the ISDN accelerator pack v1. 1 or above before installing Netscalibur's ISDN driver. Therefore, before you install the Microsoft ISDN Accelerator Pack from the Netscalibur Wizard CD, choose "Do not install a driver (Windows will not prompt you again)" when Windows 95 detects the Netscalibur or choose "Cancel" if you have Windows 95 OEM services release 2 . 2. If you accidentally select "Disk provided by manufacturer. " then you should do an uninstall as described in page 6 before continuing with the setup in step 12. 3. Perform a Scandisk operation before installing the drivers. The setup program needs to modify the registry data and copy files to your hard disk. [. . . ] 1 Click on the Network icon in the Control Panel. If you already have RAS (remote access service) installed in the system, please remove RAS before installing Netscalibur's NT driver. 2 When Windows NT 3. 51 prompts you to install a network card, click on the NO button to skip. Then click on the Add Adapter button to add the Netscalibur. [. . . ]