User manual TYAN S8226

[. . . ] S8226 Version 1. 0 Copyright Copyright © 2010 MiTAC International Corporation. No part of this manual may be reproduced or translated without prior written consent from MiTAC International Corporation. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN® is a trademark of MiTAC International Corporation. AMD® is a trademark of AMD® Corporation. [. . . ] Yes: lets the operating system configure Plug and Play (PnP) devices not required for boot if your system has a Plug and Play operating system. No / Yes PCI Latency Timer This setting controls how many PCI clocks each PCI device can hold the bus before another PCI device takes over. When set to higher values, every PCI device can conduct transactions for a longer time and thus improve the effective PCI bandwidth. Values in units of PCI clocks for PCI device latency timer register 64 / 32 / 96 / 128 / 160 / 192 / 224 / 248 Allocate IRQ to PCI VGA Yes: assigns IRQ to PCI VGA card if card requests IRQ. Yes / No Palette Snooping This is the default setting and should not be changed unless the VGA card manufacturer requires Palette Snooping to be Enabled. Enabled: informs the PCI devices that an ISA graphics device is installed in the system so the card will function correctly. Disabled / Enabled 63 http://www. tyan. com PCI IDE Bus Master Enabled: BIOS uses PCI bus mastering for reading / writing to IDE drives. Enabled / Disabled 64 http://www. tyan. com 3. 5 Boot Menu Main Boot Settings  Boot Settings Configuration  Boot Device Priority  Hard Disk Drives Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Configures settings during System Boot. ← Select Screen ↑↓ Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit 3. 5. 1 Boot Settings Configuration Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Boot Settings Configuration Quick Boot Quiet Boot AddOn ROM Display Mode Bootup Num-Lock Wait for ‘F1’ if Error Hit ‘DEL’ Message Display Interrupt 19 Capture Endless Boot [Disabled] [Disabled] [Force BIOS] [On] [Enabled] [Enabled] [Enabled] [Disabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system. ← Select Screen ↑↓ Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit Quick Boot This option allows user bypass BIOS self test during POST. Enabled / Disabled Quiet Boot Disabled: displays normal POST messages. Enabled: displays OEM log instead of POST messages. Disabled / Enabled Add On ROM Display Mode Allows user to force BIOS/Option ROM of add-on cards to be displayed during quiet boot. Force BIOS / Keep Current 65 http://www. tyan. com Boot Up Num-Lock Selects Power-on state for Numlock. On / Off Wait for ‘F1’ If Error Waits for F1 key to be present if error occurs. Enabled / Disabled Hit ‘DEL’ Message Display Displays “Press DEL to run Setup in POST”. Enabled / Disabled Interrupt 19 Capture Enabled: allows option ROMs to trap interrupt 19. Enabled / Disabled Endless Boot Enable/Disable endless loop boot from BBS table. Enabled / Disabled 66 http://www. tyan. com 3. 5. 2 Boot Device Priority Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Boot Device Priority 1st Boot Device [xx, xxx-xxxxx:xxx] Specifies the boot sequence from the available devices. A device enclosed in parenthesis has been disabled in the corresponding type menu. ← Select Screen ↑↓ Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit Set your boot device priority. [. . . ] TYAN® also ranks high for its commitment to fast and friendly customer ® support through email. By offering plenty of options for users, TYAN serves multiple market segments with the industry's most competitive services to support them. "TYAN's tech support is some of the most impressive we've seen, with great response time and exceptional organization in general" - Anandtech. com Help Resources: 1. See the beep codes section of this manual. [. . . ]