User manual TYAN S8812

[. . . ] S8812 Version 1. 1 Copyright Copyright © 2010 MiTAC International Corporation. No part of this manual may be reproduced or translated without prior written consent from MiTAC International Corporation. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN® is a trademark of MiTAC International Corporation. AMD® is a trademark of AMD® Corporation. [. . . ] Enabled / Disabled Legacy USB1. 1 HC Support Enables support for legacy USB. Auto option disables legacy support if no USB devices are connected. Enabled / Disabled 70 http://www. tyan. com 3. 3. 11 Hyper Transport Configuration Coherent HT Link Speed Configure Coherent HT frequency. Auto / 400MHz / 600MHz / 800MHz / 1GHz / 1. 2GHz / 1. 4GHz / 1. 6 GHz 1. 8GHz / 2. 0GHz / 2. 2GHz / 2. 4GHz / 2. 6GHz / 2. 8GHz / 3. 0GHz / 3. 2GHz Coherent HT Link Width Configure Coherent HT Width 8bit / 16bit NonCoherent HT Link Speed Configure NonCoherent HT frequency. Auto / 400MHz / 600MHz / 800MHz / 1GHz / 1. 2GHz / 1. 4GHz / 1. 6 GHz 1. 8GHz / 2. 0GHz / 2. 2GHz / 2. 4GHz / 2. 6GHz NonCoherent HT Link Width Configure NonCoherent HT Width 8bit / 16bit 71 http://www. tyan. com 3. 4 PCI/PnP Menu Clear NVRAM Clear NVRAM during system Boot. No / Yes Plug & Play O/S No: lets the BIOS configure all the devices in the system. Yes: lets the operating system configure Plug and Play (PnP) devices not required for boot if your system has a Plug and Play operating system. No / Yes PCI Latency Timer This setting controls how many PCI clocks each PCI device can hold the bus before another PCI device takes over. When set to higher values, every PCI device can conduct transactions for a longer time and thus improve the effective PCI bandwidth. Values in units of PCI clocks for PCI device latency timer register 64 / 32 / 96 / 128 / 160 / 192 / 224 / 248 Allocate IRQ to PCI VGA Yes: assigns IRQ to PCI VGA card if card requests IRQ. Yes / No 72 http://www. tyan. com Palette Snooping This is the default setting and should not be changed unless the VGA card manufacturer requires Palette Snooping to be Enabled. Enabled: informs the PCI devices that an ISA graphics device is installed in the system so the card will function correctly. Disabled / Enabled PCI IDE Bus Master Enabled: BIOS uses PCI bus mastering for reading / writing to IDE drives. Enabled / Disabled Offboard PCI/ISA IDE Card Some PCI IDE cards may require this to be set to the PCI slot number that is holding the card. Auto / PCI Slot 1 / PCI Slot 2 / PCI Slot 3 / PCI Slot 4/ PCI Slot 5 / PCI Slot 6 73 http://www. tyan. com 3. 5 Boot Menu Quick Boot This option allows user bypass BIOS self test during POST. Enabled / Disabled Quiet Boot Disabled: displays normal POST messages. Enabled: displays OEM log instead of POST messages. Disabled / Enabled Add On ROM Display Mode Allows user to force BIOS/Option ROM of add-on cards to be displayed during quiet boot. Force BIOS / Keep Current Boot Up Num-Lock Selects Power-on state for Numlock. On / Off 74 http://www. tyan. com PS/2 Mouse Support Select support for PS/2 Mouse. Auto / Enabled / Disabled Wait for ‘F1’ If Error Waits for F1 key to be present if error occurs. Enabled / Disabled Hit ‘DEL’ Message Display Displays “Press DEL to run Setup in POST”. [. . . ] TYAN® also ranks high for its commitment to fast and friendly customer ® support through email. By offering plenty of options for users, TYAN serves multiple market segments with the industry's most competitive services to support them. "TYAN's tech support is some of the most impressive we've seen, with great response time and exceptional organization in general" - Anandtech. com Help Resources: 1. See the beep codes section of this manual. [. . . ]