User manual TYAN TEMPEST II

[. . . ] Introduction 1. 1 Preface S1462 is a Dual Intel Pentium based PC/AT mainboard. With 75MHz thru 166MHz CPU, PCI local bus, EISA bus, it can be used with the fastest PC/ AT systems. 1. 2 Key Features * Single or Dual Pentium based PC/AT compatible mainboard with Intel Neptune chipset * 4 Master/Slave PCI Bus slots, 5 EISA Bus slots (4 master). * Supports Single or Dual Pentium Processors (75MHz thru 166MHz). * Supports true 64 bits CACHE and DRAM access mode. [. . . ] SAVE & EXIT SETUP ROM EISA BIOS (2B597G00) CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP BIOS FEATURED SETUP CHIPSET FEATURES SETUP PCI SLOT CONFIGURATION LOAD SETUP DEFAULTS ESC : Save & Exit Setup F10 : Quit :Select Item :Change Color PASSWORD SETTING IDE HDD AUTO DETECTION DAVE & EXIT SETUP EXIT WITH OUT SAVING Save to CMOS and EXIT (Y/N)?N (Shift)F2 Time, Date, Hard Disk Type, . . . . . Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS SRAM. Type "N" will return to Setup Utility. 4. 14. KEYBOARD SETTING FUNCTION After booting the O. S. , there are some special functions used by the keyboard as follows: "CTRL_ALT_DEL" -Pressing these keys simultaneously will cause the system to WARM START (Soft Reset) "CTRL_ALT_[+]" -Pressing these key simultaneously will change the system speed to high speed (Turbo, all cache memory enable) 5. 0 AMIBIOS and WINBIOS WINBIOS Setup has a graphical user interface that permits mouse access , and is so compact that it can reside on the same ROM as the system BIOS. The system configuration parameters are set via WINBIOS Setup. Since WINBIOS Setup resides in the ROM BIOS, it is available each time the computer is turned on. The WINBIOS Setup consists of the following option groups: 1. Set-up . Standard Set-up . Advanced Set-up . Chipset Set-up 2. Utility . Fail Safe 5. 1 Standard Setup Options Date, Day and Time Configuration Select the Standard Option, Select the Date and Time Icon. The current values for each category are displayed. Enter new value through the keyboard. S1462-001-01 40 Primary Master Primary Slave Select one of these hard disk drive Icons to configure the drive named in the option. WINBIOS supports up to four IDE hard disk drives: the primary master, primary slave, secondary master and secondary slave. If the hard disk drive is an IDE drive, select DETECT PRIMARY or DETECT SLAVE from the Utility Setup Option Section of the WINBIOS Setup Main Menu to have WINBIOS automatically detect the IDE drive parameters and report them to this screen. The SCSI must be selected if SCSI Disk Drive was connected. You can also enter the hard disk drive parameters. Hard disk type 47 is the user-definable drive type. The drive parameters are: Type, Cylinders, Heads, Write precompensation, Landing Zone, Sectors and Capacity. Floppy Drive A: Floppy Drive B: Move the cursor to these fields via up and down arrow key and select the floppy type. The setting are 360 KB 5 1/4 inch, 1. 2MB 5 1/4 inch, 720MB 3 1/2 inch, and 1. 44MB 3 1/2 inch. 5. 2 Advanced Setup The WINBIOS Setup options decribed in this section are selected by choosing the Advanced Setup Icon from the WINBIOS Setup Main Manu. Typematic Rate (Chars/Sec) Set the rate at which characters on the screen repeat when a key is pressed and held down. The Optimal setting is 30 characters per second. The Fail-Safe default setting is disabled. [. . . ] 8D Setup option are programming, mouse check and init. Going for HD contoller reset 8F HD controller reset done. Floppy setup to be done next 91 Floppy setup complete. HD HD setup to be next 94 HD setup done. [. . . ]