User manual TYAN THUNDER I7500 PRO

[. . . ] Thunder i7500 Pro /// Revision 1. 00 S2721 Copyright © TYAN Computer Corporation, 2002. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Thunder i7500 Pro S2721 are trademarks of TYAN Computer Corporation. [. . . ] 360KB, 5 ¼" 1. 2MB, 5 ¼" 720KB, 3 ½" 1. 44MB, 3 ½" 2. 88MB, 3 ½" Disabled Floppy A Floppy B Defines the floppy drive type. 3. 5 ­ Boot Settings Configuration Options related to startup settings can be altered through the following. Quick Boot Quiet Boot Add-On Rom Display Mode Boot up Num-Lock PS/2 Mouse Support Typematic Rate System Keyboard Enabled Disabled Enabled Disabled Force BIOS Keep Current On Off Enabled Disabled Fast Slow Present Unavailable Enabled Disabled Enabled Disabled Enabled Disabled When set to Enabled, some self-tests will be skipped during POST. If set to Enabled, OEM logo will be displayed instead of POST messages. This setting toggles the Add-On ROM video display mode. Specifies whether Num-Lock will be on or off during bootup. Will allow continual boot even if the keyboard is not attached. Toggles checking of system memory for corruption. If Enabled, you will have to press F1 for the system to continue booting if an error is detected during POST. Toggles display of pressing DEL key to enter BIOS. Parity Check Wait for F1 if "error" Hit "Del" Message 28 http://www. TYAN. com 3. 6 ­ Super IO Configuration Options related to the IO interface can be altered through the following. Enabled Disabled Auto 3F8, 2F8 3E8, 2E8 Output Only Bi-directional EPP ECP Parallel Port IRQ IRQ 7 IRQ 5 Toggles use of serial ports 1 and or 2. Enabling ports also requires you to enter the I/O address for that port unless you select Auto. These options are dependent on the IRQ and vice versa. Standard one-way protocol for parallel devices. Two-way protocol Enhanced Parallel Port may provide higher bandwidth if an EPP compliant device is used (e. g. Enhanced Compatibility Port may provide higher bandwidth if an ECP compliant device is used (e. g. Sets the interrupt request for the parallel port. (IRQ 7 and IRQ 5 both can be defaults. ) Serial Port 1, 2 Address Parallel Port Address Parallel Port Mode 3. 7 ­ Onboard Device Configuration Options related to onboard devices can be altered through the following. Onboard ATI RageXL Video Onboard 82551 Onboard 82546 Onboard SCSI Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Toggles the onboard ATI video graphics. Toggles the onboard SCSI controller. 3. 8­ USB Configuration Options related to USB can be altered through the following. USB Function Legacy USB Support Enabled Disabled Enabled Disabled Auto Enabled Disabled Auto Enabled Disabled Toggles the onboard USB ports. Toggles the use of onboard USB ports in DOS. Toggles Zip drive emulation on USB ports when in use. [. . . ] PCI card that allows a RAID card to use the onboard SCSI chip, thus lowering cost of RAID solution ZIF Socket (Zero Insertion Force socket): these sockets make it possible to insert CPUs without damaging the sensitive CPU pins. The CPU is lightly placed in an open ZIF socket, and a lever is pulled down. This shift the processor over and down, guiding into the board and locking it into place. 42 http://www. TYAN. com Technical Support If a problem arises with your system, you should turn to your dealer for help first. Your system has most likely been configured by them, and they should have the best idea of what hardware and software your system contains. [. . . ]