User manual TYAN THUNDER I7501 XTREME

[. . . ] Thunder i7501Xtreme Covers models: /// S2726 S2726UG5N/S2726G5N Revision 1. 01 Copyright © TYAN Computer Corporation, 2002-2003. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Thunder i7501Xtreme S2726 are trademarks of TYAN Computer Corporation. [. . . ] This setting toggles the Add-On ROM video display mode. Specifies whether Num-Lock will be on or off during bootup. Will allow continual boot even if the keyboard is not attached. Toggles checking of system memory for corruption. If Enabled, you will have to press F1 for the system to continue booting if an error is detected during POST. Toggles display of pressing DEL key to enter BIOS. Parity Check Wait for F1 if "error" Hit "Del" Message 3. 6 ­ Super IO Configuration Options related to the IO interface can be altered through the following. Serial Port 1, 2 Address Parallel Port Address Enabled Disabled Disabled 3F8, 2F8 3E8, 2E8 Output Only Bi-directional EPP ECP Toggles use of serial ports 1 and or 2. Enabling ports also requires you to enter the I/O address These options are dependent on the IRQ and vice versa. Standard one-way protocol for parallel devices. Two-way protocol Enhanced Parallel Port may provide higher bandwidth if an EPP compliant device is Enhanced Compatibility Port may provide higher bandwidth if an ECP compliant device is used). Parallel Port Mode 27 http://www. TYAN. com 3. 7 ­ Onboard Device Configuration Options related to onboard devices can be altered through the following. Onboard ATI RageXL Video Onboard 82551 Onboard 82546 #1 Onboard 82546 #2 Onboard SCSI Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Toggles the onboard ATI video graphics. Toggles the onboard SCSI controller. 3. 8­ USB Configuration Options related to USB can be altered through the following. USB Function Legacy USB Support USB Zip Emulation Type USB Beep Message Enabled Disabled Enabled Disabled Auto Enabled Disabled Auto Enabled Disabled Toggles the onboard USB ports. Toggles the use of onboard USB ports in DOS. Toggles Zip drive emulation on USB ports when in use. Toggles USB beep error messaging. 3. 9 ­ PCIPnP Options related to the Plug and Play PCI settings interface can be altered through the following. Yes No Yes No 32, 64, 96, 128, 160, 192, 224, 248 Yes No Enabled Disabled Toggles the option of letting the OS take care of IRQ routing or the BIOS. Select Yes to let the OS manage IRQ settings. Resets BIOS area where IRQ and DMA settings are stored. Leave on 64 for best combination of performance and stability. Palette Snooping can fix color problems associated with non-standard video cards such as MPEG decoders. Toggles the onboard IDE controllers to operate in BusMaster mode. Plug & Play OS Reset Config Data PCI Latency Timer Allocate IRQ to PCI VGA Palette Snooping PCI IDE BusMaster Offboard PCI/ISA IDE Card IRQ 3, 4, 5, 7, 9, 10, 11, 14, 15 DMA Channel 0, 1, 3, 5, 6, 7 Enabled Disabled Auto Enables the system to recognize and boot Enabled from an add-in IDE controller card. [. . . ] By adding SMDC, Tyan's server board becomes a highly manageable and IPMI compatible system with all the advanced features suggesting in IPMI Spec. More detailed information on Tyan's SMDC card can be found on our website: Http://www. Tyan. com 42 http://www. TYAN. com Appendix IV: Riser Cards Please check with your distributor for these riser cards or check http://www. etyan. com to purchase the desired card(s). 43 http://www. TYAN. com Appendix V: Pinouts of onboard jumpers/headers Pinouts for the following jumpers/headers are listed: j22, j34, j42, j50, j51, j53, j55, j58 J22. . . . . . . . . . . . . . . . . . Onboard 4 pin speaker header J22 Speaker header Pin 1 = VCC* Pin 2 = No Connect Pin3 = No Connect Pin4 = SPK * pin one is identified on the motherboard and also on page 8 J34. . . . . . . . . . . . . . . . . . . . . Serial port header (com2) Signal DCD RX TX DTR GND DSR RTS CTS RI NC/KEY DB9 PIN#(j33) 1 2 3 4 5 6 7 8 9 NC/KEY 10 PIN header(j34) 1** 3 5 7 9 2 4 6 8 10 J34 header as appears on motherboard ** pin one is identified on the motherboard and also on page 8 J53, j58, J67 & J68. . . . . . . Intel 82546 4 pin external activity J55. . . . . . . . . . . . . . . . . . . . . . . . . . . . Intel 82551 4 pin external activity 44 http://www. TYAN. com NIC four pin Header `Pin Out' j53, J55, J58, J67 & J68 Pin 1 = Link <> Yellow + *** Pin 2 = Link <> Yellow Pin3 = Speed <> Green + Pin4 = Speed <> Green - *** pin one is identified on the motherboard and also on page 8 J50 & J51. . . . . . . . . . . . . . . . . Internal USB headers J50 & j51 (labeled onboard as USB3 & USB4) Pin 1 = VCC **** Pin 2 = USBD(2&3)RPin3 = USBD(2&3) R+ Pin4 = Gnd Pin5 = Gnd **** pin one is identified on the motherboard and also on page 8. J42 . . . . . . . . . . . . . . . . . . . . . . . . SMDC ( Server Management daughter card) Odd pin 1***** 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 Signal LAD0 LAD2 GND1 GND2 GND3 GND4 I2C1DA IC24CLK GND6 I2C3DA I2C2CLK 5VSB2 PWRBTN# RSTBTN# SLPBTN# EXTSMI# Even Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 Signal LAD1 LAD3 LFRAME# PCI_CLK PCIRST# I2C1CLK GND5 I2C4DA I2C3CLK 5VSB1 I2C2DA GND7 PCIPME# SVM_IRQ# SVM_WOL# SVM_THERM# 45 http://www. TYAN. com 33 35 37 39 41 43 45 47 49 CPUNMI GPIO1 GND9 GPIO5/KEY GND10 RSVD3 RSVD5 GND12 SMALERTB# 34 36 38 40 42 44 46 48 50 GND8 GPIO2 GPIO4 PS_PWRGD RSVD2 GND11 BMC_RST# SMALERTA# GND13 ***** pin one is identified on the motherboard and also on page 8 Technical Support If a problem arises with your system, you should turn to your dealer for help first. Your system has most likely been configured by them, and they should have the best idea of what hardware and software your system contains. [. . . ]