User manual TYAN TIGER I7322DP

[. . . ] Tiger i7322DP /// Version 1. 0 S5353 Copyright Copyright © TYAN Computer Corporation, 2005. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Taro and Tiger i7322DP are trademarks of TYAN Computer Corporation. AMD, Opteron, and combinations thereof are trademarks of AMD Corporation. [. . . ] Clear all DMI event logs Setting this to `Yes' will clear the DMI event log after rebooting. Options: No / Yes 55 http://www. tyan. com 3. 4. 5 Console Redirection Main PhoenixBIOS Setup Utility Advanced Security Power Console Redirection [Disabled] [19. 2K] [PC ANSI] [CTS/RTS] [Direct] [Off] -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values Boot Exit Item Specific Help Select Com Port on BMC or motherboard. Com Port Address Baud Rate Console Type Flow Control Console connection: Continue C. after POST: F1 Help Esc Exit Select Item Select Menu Com Port Address If enabled it will use a port on the motherboard. Options: Disabled / On-board COM A / On-board COM B / NULL Baud Rate Enables the specified baud rate. Options: 300 / 1200 / 2400 / 9600 / 19. 2K / 38. 4K / 57. 6K / 115. 2K Console Type Enable the specified console type. Options: VT100/VT100, 8bit / PC-ANSI, 7bit / PC ANSI / VT100+ / VT-UTF8 / NULL Flow Control Enable Flow Control. Options: NULL / XON/XOFF / CTS/RTS Console Connection Indicate whether the console is connected directly to the system or a modem is used to connect. Options: Direct / Via modem Continue C. R. after POST Enable Console Redirection after OS has loaded. Options: Off / On 56 http://www. tyan. com 3. 4. 6 Hardware Monitor This displays critical system parameters like CPU speed, fan speeds, voltage levels and CPU temperature. Main Vcpu1 = Vcpu2= 1. 2V = 1. 5V = 1. 8V = 3. 3VSB = VBAT = 5VSB = +5V = +12V = CPU1 CPU2 Fan1 Fan2 Fan3 Fan4 Fan5 CPU1 Temp. = Ambient Temp1 = Ambient Temp2 = Ambient Temp3 = Ambient Temp4 = Auto Fan Control F1 Help Select Item Esc Exit Select Menu PhoenixBIOS Setup Utility Advanced Security Power Hardware Monitor 1. 310 V 1. 310 V 1. 179 V 1. 469 V 1. 780 V 3. 295 V 3. 182 V 5. 122 V 5. 044 V 12. 194 V 5666 RPM No Installed No Installed No Installed No Installed No Installed No Installed 48 C/118 F o o 36 C/96 F o o 97 C/206 F o o 93 C/199 F o o 93 C/199 F [Disabled] -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values o o Boot Exit Item Specific Help Auto Mode Fan Control Parameters Auto Fan Control Leave as default. Options: Enabled / Disabled 57 http://www. tyan. com 3. 5 Security These settings allow you to configure the security options for your system. Main Advanced PhoenixBIOS Setup Utility Security Power Clear Clear [Enter] [Enter] [Disabled] -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values Boot Exit Supervisor Password Is: User Password Is: Set Supervisor Password Set User Password Password on boot: F1 Help Esc Exit Select Item Select Menu Item Specific Help Supervisor Password controls the access to the setup utility. The system displays the current supervisor and user passwords. Set Supervisor Password This option allows the supervisor to set the supervisor password to restrict access to the BIOS settings. Set User Password This option allows the user to set the user password. Password on boot When enabled, the system will ask for a password at every boot. The system will continue booting only if the correct password is entered. If the wrong password is entered three times, the system will automatically shut down. Options: Disabled / Enabled 58 http://www. tyan. com 3. 6 Power These settings allow you to configure the power options for your system. Main Advanced PhoenixBIOS Setup Utility Security Power [Off] [xx:xx:xx] [On/Off] [Last State] [No] [Disabled] Boot Exit Resume On Time: Resume Time: Power Button Behavior: After Power Failure: Cabinet Monitoring: Power On By PCI/PCI-X F1 Help Esc Exit Select Item Select Menu Item Specific Help Enabled wakes the system up at a specific time. -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values Resume On Time When enabled, this allows the system to be woken up at a specified time. This time is specified by the Resume Time parameter. Options: Off / On Power Button Behavior This specifies the behavior of the system after the power button is pressed. On/Off - This powers on / powers off the system after the power button is pressed. Wake/Sleep - This wakes the system from/puts the system to sleep. [. . . ] Tyan also ranks high for its commitment to fast and friendly customer support through email. By offering plenty of options for users, Tyan serves multiple market segments with the industry's most competitive services to support them. "Tyan's tech support is some of the most impressive we've seen, with great response time and exceptional organization in general" Anandtech. com Please feel free to contact us directly for this service at techsupport@tyan. com Help Resources: 1. See the beep codes section of this manual. [. . . ]