User manual TYAN TRINITY I875P

[. . . ] Trinity i875P S5101 User's Manual Trinity i875P /// Revision 1. 01 S5101 Copyright © TYAN Computer Corporation, 2003. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Trinity, i875P and S5101 are trademarks of TYAN Computer Corporation. [. . . ] 3-27 http://www. tyan. com Trinity i875P S5101 Exit Without Saving Phoenix ­ AwardBIOS CMOS Setup Utility Chapter 3: BIOS Setup Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PC Health Status Esc: Quit F10: Save & Exit Setup Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Exit Without Saving : Select Item Save Data to CMOS PnP/PCI Configurations SAVE to CMOS and EXIT Save & Exit Setup (Y/N)?N Pressing <Enter> on this item asks for confirmation: Quit without saving (Y/N)?Y This allows you to exit Setup without storing in CMOS any change. The previous selections remain in effect. This exits the Setup utility and restarts your computer. 3-28 http://www. tyan. com Trinity i875P S5101 Chapter 4: SATA/RAID Setup (for SATA RAID model) Chapter 4: SATA/RAID Setup (for SATA RAID model) The motherboard includes the Promise PDC20378 SATA RAID controller with two Serial ATA interfaces and one Parallel ATA133 interface to support RAID 0, 1, 0+1 or Ultra ATA configuration Note: The interfaces that PDC20378 support only connect HDDs. It does NOT support ATAPI devices such as CD-ROMs, DVD-ROMs, etc. Please move your ATAPI device to the onboard IDE channel. Warning Before installing the driver into an existing system, backup any important or useful data. Failure to follow this accepted PC practice could result in data loss. ® 4. 1 ­ Getting Started Important If you wish to include your current bootable Serial or Parallel ATA drive using the Windows NT 4. x, Windows 2000, or Windows XP operating system as part of a bootable Mirrored (RAID 1) array on your SATA RAID Controller, do NOT connect the hard drive to the SATA RAID 378 controller yet. You MUST install the Windows NT4, 2000, or XP driver software first onto this drive while it is still attached to your existing hard drive controller. The PDC20378 controller supports up to two Serial ATA hard drives and two Parallel ATA hard drives 1. Configure the jumpers of the Parallel ATA hard drive you're preparing to connect to the SATA RAID controller using the proper Master, Slave, or Cable-Select settings. For more information, refer to the manual that came with your hard drive. Install all of the hard drives into the hard drive bays of your system, including the power cables. Attach the Parallel ATA cable to the hard drive(s) and to the Parallel ATA Port connector on the SATA RAID controller. Attach Serial ATA data cable to each hard drive. Then attach the other ends of the cables to one of the Serial ATA ports on the SATA RAID controller. All of the connectors are keyed so they will only attach one way. Note PDC20378 is a PCI Plug-n-Play (PnP) device. No changes are necessary in the Motherboard CMOS Setup for resources or drive types in most applications. 2. 3. 4-1 http://www. tyan. com Trinity i875P S5101 Chapter 4: SATA/RAID Setup (for SATA RAID model) 4. 2 - Creating Your Disk Array WARNING: Before installing the driver into an existing system, backup any necessary data. Failure to follow this accepted PC practice could result in data loss. [. . . ] Clear screen & display summary table 7. Program P6 class write combining Update keyboard LED & typematic rate 1. Boot attempt (INT 19h) 95h: 96h: FFh: 6-11 http://www. tyan. com Trinity i875P S5101 Technical Support Technical Support If a problem arises with your system, you should turn to your dealer for help first. Your system has most likely been configured by them, and they should have the best idea of what hardware and software your system contains. [. . . ]