User manual TYAN TRINITY KT400

[. . . ] Trinity KT400 S2495 User' Manual s Trinity KT400 /// Revision 1. 02 S2495 Copyright © TYAN Computer Corporation, 2003. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Trinity, KT400 and S2495 are trademarks of TYAN Computer Corporation. [. . . ] N/A / 3 / 4 / 5 / 7 / 9 / 10 / 11 Soft-off by PWRBTN: Defines the action of the power button when pressed. Instant-Off / 4-seconds States After Power Failure: This field lets you determine the state that your PC returns to after a power failure. If set to "Off", the PC will not boot after a power failure, if set to "On", the PC will restart after a power failure. Auto / On / Off IRQ/Event Activity Detect: Phoenix ­ AwardBIOS CMOS Setup Utility IRQ/Event Activity Detect PS2KB Wakeup Select PS2KB Wakeup from S3/S4/S5 PS2MS Wakeup from S3/S4/S5 USB Resume from S3 VGA LPT & COM HDD & FDD PCI Master PowerOn by PCI Card Wake Up On LAN / Ring RTC Alarm Resume X Date (of Month) X Resume Time (hh: mm: ss) ?IRQs Activity Monitoring [Hot Key] [Disabled] [Disabled] [Disabled] [OFF] [LPT / COM] [ON] [OFF] [Disabled] [Disabled] [Disabled] 0 0: 0: 0 [Press Enter] Item Help _________________________ Menu Level ?When Select Password, Please press ENTER key to change Password Max 8 numbers. : Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults PS2KB Wakeup Select: This item allows you to select Hot Key or Password to wake-up the system by PS2 Keyboard. When select Password, please press "ENTER" key to change password max 8 numbers. 3-20 http://www. tyan. com Trinity KT400 S2495 Chapter 3: BIOS Setup PS2KB / MS Wakeup from S3/S4/S5: This item allows you to set a Hot Key to wake-up the system by PS2 Keyboard. Disabled / Ctrl+F1 / Ctrl+F2 / Ctrl+F3 / Ctrl+F4 / Ctrl+F5 / Ctrl+F6 / Ctrl+F7 / Ctrl+F8 / Ctrl+F9 / Ctrl+F10 / Ctrl+F11 / Ctrl+F12 / Power / Wake / Any Key Note: Power and Wake are the Windows98 Keyboard button. VGA: When set to "On", any event occurring at a VGA port will awaken a system, which has been powered down. On / Off LPT & COM: When set to "LPT/COM any event occurring at a COM (serial) / LPT (printer) port will awaken ", a system, which has been powered down. LPT/COM HDD & FDD: When set to "On", any event occurring at a hard or floppy drive port will awaken a system, which has been powered down. On / Off PCI Master: When set to "Off", any event occurring to the DMA controller will awaken a system, which has been powered down. On / Off PowerOn by PCI Card: An input signal from PME on the PCI card awakens the system from a soft off state. Enabled / Disabled Wake Up On LAN / Ring: Defines whether the system will wake up if the modem is dialed into. Enabled / Disabled RTC Alarm Resume: Defines the time / date when the system will wake up. Enabled / Disabled 3-21 http://www. tyan. com Trinity KT400 S2495 IRQs Activity Monitoring: Phoenix ­ AwardBIOS CMOS Setup Utility IRQs Activity Monitoring Primary INTR IRQ3 (COM 2) IRQ4 (COM 1) IRQ5 (LPT 2) IRQ6 (Floppy Disk) IRQ7 (LPT 1) IRQ8 (RTC Alarm) IRQ9 (IRQ2 Redir) IRQ10 (Reserved) IRQ11 (Reserved) IRQ12 (PS/2 Mouse) IRQ13 (Coprocessor) IRQ14 (Hard Disk) IRQ15 (Reserved) [On] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] Chapter 3: BIOS Setup Item Help _________________________ Menu Level ?? : Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Primary INTR: When set to "On", any event occurring at will awaken a system which has been powered down. On / Off IRQs 3 ~ 15: Allows you to set system to monitor IRQs 3 ~ 15 for activity to awaken system from a power management mode. 3-22 http://www. tyan. com Trinity KT400 S2495 Chapter 3: BIOS Setup 3. 7 ­ PnP/PCI Configurations Options related to all the configurations of PnP / PCI resources. Phoenix ­ AwardBIOS CMOS Setup Utility PnP / PCI Configurations PNP OS Installed Reset Configuration Data Resources Controlled By X IRQ Resources PCI / VGA Palette Snoop PCI Device List [No] [Disabled] [Auto (ESCD)] [Press Enter] [Disabled] [Enabled] Item Help _________________________ Menu Level ?Select Yes if you are using a Plug and Play capable operation system Select No if you need the BIOS to configure n0n-boot devices : Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults PNP OS Installed: Select " Yes", if you are using a PNP OS, otherwise select "No". Yes / No Reset Configuration Data: This setting allow you to clear ESCD data. Enabled / Disabled Resources Controlled By: Default whether system resources are controller by BIOS or by user. [. . . ] Clear screen & display summary table 7. Program P6 class write combining Update keyboard LED & typematic rate 1. Boot attempt (INT 19h) 95h: 96h: FFh: 5-14 http://www. tyan. com Trinity KT400 S2495 Technical Support Technical Support If a problem arises with your system, you should turn to your dealer for help first. Your system has most likely been configured by them, and they should have the best idea of what hardware and software your system contains. [. . . ]