User manual ULINE ECHELON 2015R INSTALLATION GUIDE

[. . . ] TM Installation Guide 2015R -- Refrigerator www. U-LineService. com Phone (414) 354-0300 · FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 · FAX (414) 354-5696 OnlineService@U-Line. com ©2005 U-Line Corporation 02/2005 2015R -- Refrigerator TM Contents Exterior Cleaning . Side-By-Side Installation Instructions . Custom 1/4'' Door Panel Insert . 4 4 5 5 5 6 7 7 8 12 12 13 13 13 14 14 14 15 15 16 1 Follow Safety Precautions IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit. [. . . ] Refer to Figure 16 for exact specifications. www. U-LineService. com 8 02/2005 TM 2015R -- Refrigerator 13/32" 0. 177" Dia. (#16 Drill) x 11/16" Deep 3/8" 13/32" 4. Drill hole for upper door hinge (top of panel) (see Figure 16, Top View). 0. 177" diameter (#16 drill) x 11/16" deep 5. Drill hole for lower door hinge (see Figure 16, Bottom View). 5/16" diameter x 1/4" deep 3/8" 13/16" Top View Door Bottom: 5/16" Dia. x 1/4" Deep Chamfer 1/32" x 45° Bottom View CAUTION 1/8" 13/32" 1/32" R 1/8" 1/8" It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed. 13/16" 1-17/32" 7/16" Installation Instructions Removing Existing Door 1. Remove the door shelves by first pulling shelves up at a 45° angle then straight out (see Figure 33 on Page 14). 3/4" Side View 1/8" R 5/16" Dia. x 1/2" Deep 13/16" Back View Figure 16 Route notch in top corner of overlay panel as shown (see Top and Side Views). Top of notch is entire depth of panel, front to back. Width: 13/16" Depth: 1/8" Route notch in backside of top corner of overlay panel (see Back and Side Views). Width: 13/16" Depth: 1/8" Height: 1-17/32" from top edge of panel (less 1/8" for depth of notch on top of panel) Radius of corner notch: 1/8" (see Back View) 3. Drill holes for pivot plate mounts (see Figure 16, Back View). 5/16" diameter x 1/2" deep, from the routed surface 2. Remove top hinge screw pin (7/64" hex key or Phillips screwdriver, depending on your unit's construction). Remove the door by tilting forward and lifting off the bottom hinge pin. Pull door gasket out of the groove (top edge of door only). Start in the middle and pull outward, moving toward the edge (see Figure 17). This may take some force. New Handle Old Handle Figure 17 Figure 18 CAUTION Be careful not to drill too deep!Drilling holes too deep may destroy your door panel. 4. Remove the three screws located on the back of the handle (see Figure 18). 02/2005 9 www. U-LineService. com 2015R -- Refrigerator TM 5. (This handle will be replaced with the Modified Handle included in the Full Overlay Door Panel Kit. ) 6. [. . . ] Go on to 8 Install the Unit. WARNING SHOCK HAZARD -- Electrical Grounding Required. · Never remove the round grounding prong from the plug and never use a two-prong grounding adapter. · Never use an extension cord to connect power to the unit. Go on to 7 Level the Unit. Installation Tip If the room floor is higher than the floor in the cut-out opening, adjust the rear feet to achieve a total unit rear height of 1/8" less than the opening's rear height. [. . . ]