User manual ULINE ECHELON 2075WC

[. . . ] É c h e l o nTM ® U S E R M A N U A L U-LINE CORPORATION LIMITED WARRANTY U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year warranty period for all U-Line products U-Line shall: (1) at U-Line's option, repair any product or replace any part of a product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part. During years two through five of the warranty period for the sealed system, U-Line shall:. (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. [. . . ] Apply Minwax Water-Based Wood Stain to wood with a synthetic foam brush. Stain must penetrate approximately 3 minutes. After this period, while stain is still wet, take a stain dampened rag and remove all excess stain. Wipe in the direction of the grain with medium pressure to achieve the desired stain color. This will even out the color of the wood. Allow stain to dry for a minimum of 3 hours before finishing. If desired sand the wood with very fine sandpaper to smooth the surface from the staining process. Apply one coat of Minwax Ultra Fast-Drying Polycrylic Protective Finish with a synthetic foam brush to the wood. This finish should be applied in a thin coat following the direction of the grain. First apply the finish to the back and sides of the wood. Next apply the finish to the front side of the wood and allow to dry for two hours. Sand with very fine sandpaper (220 grit). Reapply in the same manner 3 times total. After the third coat do not sand the surface. Allow the final coat to dry for 24 hours before installing the wood to the Wine Captain® racks. 4. 7. 8. 12 LEVELING THE UNIT Position the unit on a flat, level surface, capable of supporting the entire weight of the unit when full. This unit contains four adjustable leveling legs. Turn the legs clockwise to raise and counterclockwise to lower (see Figures 3 & 4). CHECK LEVEL TURN FOOT TO ADJUST UL105 UL314 Figure 3 Figure 4 REVERSING THE DOOR All Wine Captain® models (except Stainless Steel models which must be ordered left or right hand opening) are field reversible for left or right hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side (see Figure 5). UL318 Figure 5 13 User's Manual To reverse the door: 1. Remove top hinge screw pin (7/64" Allen wrench) from cabinet (see Figure 6). Remove door by tilting forward and lifting off bottom hinge pin. Remove top hinge (3 screws), reinstall hinge screw pin, and remount on opposite side BOTTOM (see Figure 8). HINGE SCREW PIN UL313 Figure 8 4. UL310 Figure 6 2. [. . . ] Slide the rack on the channel at an angle until the rack is in the channel. Continue sliding until the rack is all the way into the Wine Captain®. UL302 Figure 19 BULB REPLACEMENT To replace the light bulb in your Wine Captain®: 1. Remove the light housing cover by sliding the cover towards the tab, swinging the end opposite of the tab down and pulling down and away (see Figure 20). Replace bulb with genuine U-Line replacement. [. . . ]