User manual ULINE ORIGINS 15R

[. . . ] User's Manual ICE-MAKERS, COMBOS AND REFRIGERATORS U-LINE CORPORATION LIMITED WARRANTY U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year warranty period for all U-Line products U-Line shall: (1) at U-Line's option, repair any product or replace any part of a product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part. During years two through five of the warranty period for the sealed system, U-Line shall:. (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. [. . . ] Reinstall grille (1 screw). 17 User's Manual REVERSING A STAINLESS STEEL DOOR Stainless Steel models are field reversible for left or right hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side (see Figure 26) as follows: 1. Remove the bottom hinge (2 screws) from door. Remove top hinge (4 screws) from cabinet. Invert and install on bottom, opposite side of cabinet. Remove bottom hinge (4 screws) from cabinet. Invert and install on top, opposite side of cabinet. Align as required to assure proper door seal. 8. ALIGNING THE DOOR For proper door alignment: 1. Loosen top and bottom hinge screws (see Figure 16). Assure gasket is firmly in contact with cabinet all the way around the door (no gaps). Tighten top hinge screws. 18 NOTE When inspecting door alignment, make sure that the light switch bracket (where equipped) makes contact with the light switch plunger (see Figure 27). Also, make sure that the door gasket is not pinched too tightly on the hinge side of the door. UL130 Figure 27 CUSTOM DOOR PANEL INSERT INSTALLATION A custom door panel insert can be installed in most U-Line units. The door will accept a flat or raised panel. The maximum panel thickness where inserted into the door reveal (channel) is 1/4" thick. For raised panels, the depth of the reveal is 1/4" on the sides and bottom, and 1/2" on the top. The size of the door panel insert is shown below: The door panel insert must not weigh more than 20 lbs. Custom Door Panel Dimensions B Model BI-95 BI-98 75 Series 75 SS 29 Series 15 Series 15 SS A 13­15/32" 15­15/16" 28­5/32" 29­13/32" 21­13/32" 28­5/32" 29­13/32" B 12­15/16" 13­15/16" 22­15/16" 22­15/16" 19­13/16" 13­15/16" 13­15/16" A SS - Stainless steel units NOTE Model SP18 does not accept custom door panels. 19 User's Manual Install the insert as follows: ! Insert edges may be SHARP!Remove top hinge screw pin (large Phillips head, see Figure 28). Remove door, being careful not to scratch top of door on hinge. Pull door gasket out of groove (top edge of door only). Start in the middle and pull outward, moving toward the edge (see Figure 29). [. . . ] DANGER ! ELECTROCUTION HAZARD NEVER attempt to repair or perform maintenance on the unit until the main electrical power has been disconnected. Troubleshooting -- What to check when problems occur Problem No interior light The unit is not cold enough Possible Cause Loose or burned out bulb Light staying on Remedy Tighten or replace bulb. See LIGHT BULB REPLACEMENT Adjust door so light switch bracket contacts switch plunger. See CARE AND CLEANING Airflow must not be obstructed to front grille. See INSTALLATION Turn control knob CLOCKWISE to set temperature colder. [. . . ]