User manual UNI-T DT 830E

[. . . ] For units equipped with externally accessible fuse receptacle: Replace fuse with same type and rating only. Electromagnetic Compatibility Operation is subject to the following conditions: ·This device may not cause harmful interference. ·This device must accept any interference received, including interference that may cause undesired operation. ·Use only shielded interconnecting cables. ·Operation of this unit within significant electromagnetic fields should be avoided. DECLARATION OF CONFORMITY nufacturer's Name: nufacturer's Address: clares that the product: Product Name: Product Options: nforms to the following Product Specifications: Safety: EMC: pplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and EMC Directive 89/336/EEC as amended by Directive 93/68/EEC. [. . . ] Some information contained in this manual y also be inaccurate due to undocumented changes in the product or operating system since this version of the manual was completed. The ormation contained in this version of the owner's manual supersedes all previous versions. Page1 Congratulations on the purchase of your new WhammyTM Pedal. When DigiTech invented the WhammyTM pedal, it was the most revolutionary and innovative pedal to hit the guitar since the he wah wah. Nearly a decade later, in response to your demands, we have gone to painstaking engths to bring back the original WhammyTM. Every last detail was considered as we recreated his classic pitch bending effect. However, we strengthened the rugged steel chassis to endure the erils of the stage better, the addition of a MIDI input provides more flexibility, preset LEDs proide a visual indication of your selection, and the Dive Bomb setting bends your signal a full 3 ctaves down. We are proud to bring back this pedal, and we're proud that you wanted it. Although the WhammyTM has an extremely intuitive user interface, this User's Guide will help ou understand the WhammyTM functions and allow you to get the most out of your purchase or years to come. ncluded Items he utmost care was taken while your WhammyTM was being manufactured. Everything should e included and in perfect working order. Before you get started, please make sure that the ollowing items have been included: WhammyTM Pedal PS750 or PS913 Power Supply User's Guide Warranty Card anything is missing, contact the factory at once. Please take a moment to complete your warranty card. It is your safeguard should a problem arise with your WhammyTM. User's Guide Guided Tour Detailed Descriptions 12 5 6 3 4 7 8 9 . Preset Knob - This knob is used to select the WhammyTM (bend), Harmony intervals, or Detune range controlled by the treadle. 2 Oct Dn - Bends your input note two octaves down. Dive Bomb - Bends your input note three octaves down. Drop Tune - Bends your input note two semi-tones down with a reversed pedal action. Page5 Whammy Presets User's Guide Harmony - This group of Presets adds a harmony to your incoming signal. Both the harmony ote and the input signal are mixed together as if two guitars were playing simultaneously. As you ock the pedal back and forth, the harmony note bends between two intervals specified by the elected Preset but the input signal remains unchanged. Harmony Presets include: 2nd Up/3rd Up - Bends the harmony between a second (toe up) and a third (toe down) above the input note. Min 3rd Up/3rd Up - Bends the harmony between a minor third (toe up) and a Major third (toe down) above the input note. 3rd Up/4th Up - Bends the harmony between a third (toe up) and a fourth (toe down) above the input note. 4th Up/5th Up - Bends the harmony between a fourth (toe up) and a fifth (toe down) above the input note. 5th Up/6th Up - Bends the harmony between a fifth (toe up) and a sixth (toe down) above the input note. 4th Up/7th Up - Bends the harmony between a fourth (toe up) and a seventh (toe down) above the input note. [. . . ] Press the footswitch again to exit the MIDI set up menu. Omni Chnl 16 Chnl 15 Chnl 14 Chnl 13 Chnl 12 Chnl 11 Chnl 10 Chnl 9 Chnl 1 Chnl 2 Chnl 3 Chnl 4 Chnl 5 Chnl 6 Chnl 7 Chnl 8 User's Guide Page9 MIDI Program Changes he WhammyTM uses MIDI Program Change commands for preset selection. Presets can be elected in either an active or bypassed state. The following list outlines the program change ommands recognized by the WhammyTM, and the corresponding WhammyTM preset. MIDI Program Change # active bypass 9 26 10 27 11 28 12 29 13 30 14 31 15 32 16 33 17 34 MIDI Program Change # active bypass 1 18 2 19 3 4 5 6 7 8 20 21 22 23 24 25 User's Guide MIDI Continuous Control he WhammyTM is capable of remotely adjusting the treadle position, as well as turning the WhammyTM effect on and off through the use of MIDI continuous control commands. A value of 0 on MIDI CC11 corresponds to a toe up osition and 127 corresponds to a toe down position. MIDI CC0 is used to turn on and off the Whammy effect. Values from 0 through 64 on MIDI CC0 will turn the WhammyTM effect off, and values from 65 through 127 will turn the effect on. [. . . ]