User manual UNIDEN ANA9500 OPERATING GUIDE

[. . . ] ANA 9500 Spread Spectrum Analog PBX Cordless Telephone XFER HOLD TALK CONF MEMO 1 4 GHI 7 PRS 2 ABC 5 JKL 8 TUV 0OPER F2 F3 3 DEF 6 MNO 9 WXY CHARGE BATT POWER CHARGE , F1 F4 IN USE/HOLD PAGE/FIND Operating Guide PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture. RECHARGEABLE NICKEL-CADMIUM BATTERY WARNING n This equipment contains a Rechargeable Nickel-Cadmium Battery. n Cadmium is a chemical known to the State of California to cause cancer. n The Rechargeable Nickel-Cadmium Battery contained in this equipment may explode if disposed of in a fire. n Do not charge the Rechargeable Nickel-Cadmium Battery used in this equipment in any charger other than the one designed to charge this battery as specified in this Guide . Using another charger may damage the battery, or cause the battery to explode. RECHARGEABLE NICKEL-CADMIUM BATTERIES MUST BE RECYCLED OR DISPOSED OF PROPERLY n Residents Of Minnesota should contact 1-800-225-PRBA for information concerning reclamation and disposal of Rechargeable Nickel-Cadmium batteries. [. . . ] If the BATTERY CHARGE LED does not light, check to see that the AC Adapter is plugged in, and that the Battery Pack is seated into the Charging Compartment. Note: Charge the Standard 400 maH Battery Pack without interruption for 6-8 hours. Charge the optional 730 maH maH Battery Pack without interruption for 8-10 hours. When charging is complete, press down on the latch to remove the Battery Pack for use. Or, if you don't need the Battery pack immediately, leave it in the Charging Compartment (It will not overcharge. ) Low Battery Indicator When the Battery Pack in the Handset is low and needs to be charged, you will see a message on the display. On a Call Only the TALK button operates. Handset beeps once every 3 seconds Complete your call as quickly as possible Replace Battery pack within 20 seconds to continue call. In Standby Mode None of the buttons operate. Replace Battery Pack before making a call. Return the Handset to the Base Unit for charging or replace the Handset Battery Pack with another charged Battery Pack. 12 Cleaning the Battery Contacts To maintain a good charge, it is important to clean all charging contacts on the Handset and Base Unit about once a month. Use a pencil eraser or other contact cleaner. Do not use any liquids or solvents. XFER HOLD TALK CONF MEMO 1 4 GHI 2 ABC 3 DEF 5 JKL 6 MNO 7 PRS 8 TUV 9 WXY 0OPER # CHARGE BATT POWER CHARGE , F1 F1 F2 F2 F3 F3 F4 F4 IN USE/HOLD PAGE/FIND Contacts Contacts 13 Using Your ANA 9500 Handset Note: Operation of the ANA 9500 is performed using the Handset off the Base Unit. The exceptions are charging the Handset Battery Pack, and terminating a call with AutoStandby. The Base Unit is used to place a call on HOLD, or to Page the Handset. These operations are discussed in the Section: "Using Your ANA 9500 Base Unit". ANA 9500 Handset Controls R/VOL L MUTE Handset Earpiece Ringer Select (Standby Volume (During a Call Mode) Press VOL on the side of the Handset to select a loud or soft Earpiece volume level. Press VOL on the side of the Handset to select from RING HIGH Note: You get a vibrator alert instead of a ring tone when you set the Ringer Volume to RING OFF. L Mute RING LOW 14 Using the Handset When you pick up the Handset and press TALK, you will see: Then you'll see one of the following: Condition Line OK Indicator TALK LED LCD Display No Connection to Base Unit Channel Busy Error Tone NO SERVICE SYSTEM BUSY LINE IN USE Error Tone Line in Use Error Tone When communication is made between the Base Unit and the Handset, the screen will go to "Standby", and the phone is ready to use. If the Handset is at the range limit of the ANA 9500, you may see: Take the following action: During a Call Condition Action Warning Tone Move back in range within 20 seconds In Standby Mode Can't make or answer calls (Phone may ring intermittently) Move back within range. 15 Answering a Call When you receive a call, the Handset rings and you'll see: Handset on the Base Unit Pick up the Handset. The AutoTalk feature allows you to answer the call immediately. Handset off the Base Unit Press TALK. When you finish the call, , place the Handset back on the Base Unit. AutoStandby automatically hangs up the phone. --OR-- Press TALK to hang up the phone. Making a Call (If the Handset is on the Base Unit, pick it up. ) Press TALK. The TALK LED will light, and you'll see: If the Line is all right, enter the number you are calling. See the section on "Using Memory". ) When you finish the call, place the Handset back on the Base Unit. AutoStandby automatically hangs up the phone. -ORPress TALK to hang up the phone. 16 Feature Buttons Note: The exact operation of the Feature Buttons depends on how your PBX system is configured. [. . . ] The IN USE/HOLD LED lights steadily. CHARGE BATT POWER CHARGE IN USE/HOLD PAGE/FIND The call is now transferred to the ANA 9500, and the Desk phone is disconnected. 27 Transferring a Call to the Desk Telephone 1. Press HOLD on either the ANA 9500 Handset or Base Unit. You can now place the ANA 9500 Handset on the Base Unit. Typical Applications You can use the ANA 9500 together with a standard PBX telephone to give you effective business communications both at your desk and away from it. Contact your PBX Administrator for more information about your System. [. . . ]