User manual UNIDEN CEZ200

[. . . ] WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below. WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale. The warranty is invalid if the Product is (A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner's manual for this product. STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or its representatives in connection with the performance of this warranty. [. . . ] The pictures in this manual are used for examples only. Your actual phone may not look exactly like the pictures. Page 1 (outside) Fold line Fold line Fold line Fold line Using the Phone Boost button Volume dial Reset button Visual ringer light Flash button Tone/ pulse switch Mute button Redial button Hook switch Handset clip Ringer switch Button What it does Boost and These controls work together to change the volume. See Volume dial Changing the Audio Volume. Flash During a call: switch to a waiting call Tone/pulse Change the dial mode (see Solving Problems. ) Reset During a call: Hang up the current call and get a dial tone. During a call: press & hold to mute the microphone so callers Mute can't hear you. Ringer Turn the audio ringer (but not the visual ringer) off or on. Wall-Mounting the Phone You can mount the phone on any standard telephone wall plate where the pins are 100 Connect the cords as usual, but route the mm (315/16 inches) line cord through apart. Before putting the handset in the cradle, you need to switch the Tuck excess line cord into the handset space on the back of the phone. clip into wall mount mode as shown in Line up the notches on the the drawing base with the pins on the below. Place the phone over the plate and slide it down to lock it into place. If there's static on the line DSL broadband Internet service can cause static on telephones, but a DSL filter usually solves any problems. To get a DSL filter, call your DSL provider or look in any electronics store. To install the filter, plug the DSL filter into the wall jack and then plug your phone into the filter. Make a test call to see if the noise is gone. FCC compliance information Part 68 information DSL lter Telephone wall jack Telephone cord What Else Do I Need to Know? This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: 6NYTE##BXXXXXX (where XXXXXX stands for a specific model number). If requested, this number must be provided to the telephone company. An applicable Universal Service Order Codes (USOC) certification for the jacks used in this equipment is provided (i. e. , RJ11C) in the packaging with each piece of approved terminal equipment. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. [. . . ] NOTICE: According to telephone company reports, AC electrical surges, typically resulting from lightning strikes, are very destructive to telephone equipment connected to AC power sources. To minimize damage from these types of surges, a surge arrestor is recommended. Flip the clip from front to back. Slide the clip out of its slot. Slide it back into the slot. Rotate the clip 180 degrees. Using Call Waiting Call waiting is service provided by your local telephone provider; contact your telephone provider to subscribe to this service. If you get a Call Waiting call, the handset beeps. Press Flash to switch between the current call and the waiting call; each time you switch, there's a short pause before you're connected to the other caller. [. . . ]