User manual UNIDEN DCT748-4

[. . . ] DCT 748 SERIES OWNER'S MANUAL Contents WELCOME/FEATURES TERMINOLOGY CONTROLS & FUNCTIONS DISPLAY AND ICONS GETTING STARTED Setting up the Phone Expanding Your Phone Register the Handset Changing the Digital Security Code Installing the Beltclip Optional Headset Installation Main Menu Options Setting Menu Options 2 CALLER ID Caller ID and CIDCW (Caller ID on Call Waiting) 3 THE INTEGRATED TELEPHONE 4 ANSWERING DEVICE 6 The Integrated Telephone Answering Device 7 Turning the Answering System On/Off 7 12 14 15 15 15 16 17 26 28 28 29 30 31 32 32 33 33 34 34 Setting Your Outgoing Message (Greeting) Using Your Answering System Remote Operation 43 43 48 48 52 52 54 58 MULTI-HANDSET FEATURES Multi-Handset Features Using DirectLink Mode Intercom Room/Baby Monitor Note on Power Sources General Information 62 62 62 64 66 BASICS Using Your Phone Call Waiting Placing a Call on Hold Redialing a Call Adjusting the Ringer, Earpiece and Speaker Volume Mute Microphone Tone Dialing Switch-over Traveling Out of Range Clarity Booster Privacy Mode Conferencing Find Handset 26 ADDITIONAL INFORMATION TROUBLESHOOTING Troubleshooting Liquid Damage 67 67 69 70 70 72 PHONEBOOK 35 PRECAUTIONS & WARRANTY I. C. NOTICE INDEX MEMORY LIST REMOTE OPERATION CARD 73 75 76 77 80 Setting up the Phonebook 35 Viewing the Phonebook 39 Making Calls Using the Phonebook 40 Speed Dialing 40 Editing or Erasing a Stored Name, Phone Number, Distinctive Ring and Speed Dial 41 Copying Phonebook Locations 42 [1] www. uniden. com Welcome Congratulations on your purchase of the Uniden Multi-Handset Cordless Telephone System!This unit is different from conventional cordless telephones. When the base unit is connected to AC power and a telephone line, it can support up to four handsets. [. . . ] Setup menu and then the Answer Setup submenu. 2) Press /vol/ or /vol/ to select On or Of f . The answer LED will light if you turn the answering system on. note ·If you make an outside call or a call is received during the operation, the operation is canceled. THE INTEGRATED TELEPHONE ANSWERING DEVICE Setting Your Outgoing Message (Greeting) When you receive a call, the answering system automatically plays either the prerecorded message or your own greeting. The following message is pre-recorded: "Hello, no one is available to take your call. Please leave a message after the tone. " Recording a Personal Outgoing Message The answering system allows you to record a personal outgoing message (greeting) which the answering system automaticlly plays when you receive a call. 1) With the phone in standby mode, press select/ /audio tone. 2) During the annoucement "To record memo message, press seven. 3) After the announcement "Record Greeting, " record your greeting. 4) When you are finished recording, press 5 or 8. Your greeting will playback for confirmation. www. uniden. com ·The answer LED blinks if you set Announce Only to on. THE INTEGRATED TELEPHONE ANSWERING DEVICE [52] THE INTEGRATED TELEPHONE ANSWERING DEVICE Selecting Your Greeting The phone allows you to choose between the two outgoing messages, a prerecorded message or your own greeting. 1) With the phone in standby mode, press select/ /audio tone. 2) During the annoucement "To record memo message, press seven. 4) While the outgoing message is playing, press 6. Each time you press 6, the phone switches the outgoing message between the prerecorded and your own greeting. To delete the personal greeting, press /4 while the outgoing message is playing. The system announces "Greeting has been deleted". Announce only feature The announce only feature plays a pre-recorded outgoing message or your own personal outgoing message, but it will not allow the caller to leave a message. To set announce only, follow the steps on "Setting the Record Time" page 50. If you want to use your own greeting and you want to change your greeting to omit the prompt to leave a message, see "Recording a Personal Outgoing Message" on page 52 for instruction. The following message is pre-recorded: "Hello, no one is available to take your call. Please call again. " [53] THE INTEGRATED TELEPHONE ANSWERING DEVICE www. uniden. com Using Your Answering System The new message LED on the handset and base blink when you have new messages in your answering system. The LED stops flashing when all new messages are played back. The answering system is designed to play your new messages first. [. . . ] Press 0 then 6 to turn the answering system on. REMOTE OPERATION CARD CUT CUT REMOTE OPERATION CARD REMOTE OPERATION CARD Remote access away from home 1. Call your phone number from a touch-tone phone. During the outgoing message, press 0 and enter your PIN code. The answering system announces the number of messages stored in memory and the voice prompts. [. . . ]