User manual UNIDEN EWCI936

[. . . ] EWCI 936 UP033BH_EXI7246C. book Page 1 Wednesday, June 16, 2004 2:14 PM Contents Welcome/Features Controls and Functions Terms Used in this Manual Getting Started 2 3 5 Making Calls from Speed Dial Memory Making a Call from the Caller ID List Adjusting the Earpiece Volume Using a Headset Headset installation Making calls with the headset Receiving calls with the headset Installing the Beltclip Tone Dialing Switch-over Traveling Out-of-Range Selecting a Different Channel Finding a Lost Handset Using Call Waiting Voice Mail Waiting Indicator 36 37 37 38 38 38 39 39 40 40 40 41 41 42 43 44 47 48 51 52 54 54 54 55 56 Installing the Phone and Outdoor Weather Sensor 6 A. Choose the Best Location Base and Handset 6 B. Install the Rechargeable Battery Pack into the Handset 8 C. Connect the Base, Set up the Outdoor Weather Sensor and Charge the Handset 9 D. [. . . ] The displayed phone number dials automatically. Adjusting the Earpiece Volume To change the earpiece volume, press the /vol/ or /vol/ key during a call. Temporarily Mute Ringer If the handset is off the base while an incoming call is ringing, simply press the end key to temporarily mute the incoming ring. The ringer will sound with the next incoming call. U S IN G Y OU R P H ON E [37] USING YOUR PHONE www. uniden. com UP033BH_EXI7246C. book Page 38 Wednesday, June 16, 2004 2:14 PM Using a Headset Headset installation Your phone may be used with an optional headset, the Uniden HS910. Your phone is ready for hands-free conversations. (Headset may be purchased by calling the Uniden Parts Department or visiting the web site. See page 47. ) 1) Place the headset on your head so the speaker covers your ear. The other end of the headset should rest comfortably against the side of your head above your ear. Do not place the end of the headband against the other ear. 2) The microphone arm swings over the top of the headset so you can wear the headset on the left or right ear. Position the flexible arm so the microphone is about 2 inches away from your mouth. 3) To use the headset, plug the headset plug into the headset jack. Making calls with the headset 1) Remove the handset from the base and place the headset on your head with the earpiece over either ear. 3) Listen for the dial tone from the headset. OR U S IN G Y OU R P H ON E www. uniden. com USING YOUR PHONE [38] UP033BH_EXI7246C. book Page 39 Wednesday, June 16, 2004 2:14 PM 1) Remove the handset from the base and place the headset on your head with the earpiece over either ear. 2) Dial the number. Receiving calls with the headset 1) Place the headset on your head with the earpiece over either ear and remove the handset from the base. (If AutoTalk is on, the phone will automatically answer the call when your pick it up. ) 2) Press the talk/flash key. OR 1) If the handset is off the base, place the headset on your head with the earpiece over either ear. 2) Press the talk/flash key or any number key. (AutoTalk is on. ) Installing the Beltclip To attach the beltclip Insert the beltclip into the holes on each side of the handset. To remove the beltclip Pull both sides of the beltclip to release the tabs from the holes. U S IN G Y OU R P H ON E [39] USING YOUR PHONE www. uniden. com UP033BH_EXI7246C. book Page 40 Wednesday, June 16, 2004 2:14 PM Tone Dialing Switch-over If your telephone company requires pulse dialing, you can switchover to tone dialing after the call connects. This feature is useful when you need tone dialing to use any automated menu systems, such as telephone bank tellers, telephone prescription refills, customer support menus, etc. If your phone is set to pulse dialing mode, make your call normally. Once your call connects, press the /tone/ key. Any digits you enter from then on will be sent as tone digits. [. . . ] Notice TERMINAL EQUIPMENT NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. [. . . ]