User manual UNIDEN EXLA8950

[. . . ] Introduction TO YOUR NEW PHONE Thank you for choosing the Uniden EXLA 8950 cordless telephone. This phone is designed to exacting standards that provide reliability, long life and outstanding performance. Note: Some illustrations in this manual may differ from the actual unit for explanation purposes. INTRODUCTION Features · 900 MHz Extended range · Secure Digital Transmission · Integrated Answering Device · Long Distance Manager · 10 Number Memory · 32 Digit Redial · Flash · Pause · Pulse / Tone Dialing · 7 Day Standby Battery Life · 7 Hour Talk Time · Handset Earpiece and Ringer Volume Control · Speakerphone · 3-Way Conference Operation · Intercom Controls and functions 1 2 5 14 15 16 17 18 6 7 8 9 10 11 12 13 1 talk batt mute vol talk flash mute Long Dst mem 2 abc 5 jkl 8 tuv 0 oper int'com 3 def 6 mno 9 wxyz 4 ghi 7pqrs tone 3 redial/p ringer chan extended range 19 20 21 4 DIGITAL 900MHz 23 24 25 26 27 28 29 30 31 32 22 33 clock pin status speaker volune delete play 34 35 36 37 38 39 40 41 42 DIGITAL greeting voice memo answer on/off speaker page/int'com 1. 21. Handset antenna Headset jack cover Handset battery compartment Handset ring switch Handset earpice Talk/Battery LED Talk key Volume down key Flash key Tone key Redial/Pause key Intercom key Handset microphone Mute LED Volume up key Long Distance Manager key Memory key Mute key Channel key Ringer select key Handset charging contact 22. [. . . ] (Number zero through six displays on the base as each day is announced. ) Press clock again to select the day. Next, press or until you hear the correct hour setting. Numbers 1 through 12 display on the base as each hour is announced. Press clock again to select the correct time. If you don't set the clock within two minutes, the system returns to standby. 3 4 5 6 Press or until you hear the correct time setting. Numbers 1 through 59 display on the base as each minute is announced. Press clock again to select the correct time. or until you Press clock again to end the time/day setting. The EXLA 8950 announces the time that you have set. 26 Setting your greeting When you receive a call, the answering system automatically plays either a preset message or your own greeting. ª Preset Message The following message is prerecorded: "Hello, no one is available to take your call. Please leave a message after the tone. " ª Recording your personal outgoing message (Greeting) 1 Press and hold greeting until you hear a long tone. Start recording your message immediately after you hear the long tone end. When you are finished recording your message, press greeting or play . A long tone sounds and your message plays back on the phone. 2 You can record a greeting up to 30 second. ª Choosing between two outgoing messages 1 Stand within 12 inches in front of the microphone and speak clearly when recording your outgoing message. Press greeting to play the outgoing message. While the message is playing, press greeting again to select between your personal greeting and the prerecorded greeting. 2 27 Selecting the message record time You can set your answering system to record messages up to one or four minutes long. One minute option: move the REC TIME switch to 1. Four minutes option: move the REC TIME switch to 4. REC TIME ANN/4/1 ª Announce only feature: The announce only feature plays an outgoing message, but it will not allow the caller to leave a message. Move the REC TIME switch to the ANN position. The message counter LED displays " " when system is on standby. Prerecorded outgoing message for Announce only feature is: "Hello, no one is available to take your call. " Selecting a PIN code To play your messages from a remote location, you will need to enter a two-digit Personal Identification Number (PIN) code (00-99). To select a PIN, perform the following steps. 1 2 Press or multiple times to scroll through numbers on the display. On the base, press and hold pin button until a beep sounds, and the LED displays 00. To set the first number, press or to scroll from 00 to 90. When the desired number appears in the display, press pin . To set the second number, press or to scroll from 0 to 9. [. . . ] · Make sure the AC adapter is plugged into the base unit and wall outlet. · Disconnect the AC adapter for a few minutes, then reconnect it. · Reset the digital security code (See page 36). Charge the battery on the base unit for 12-15 hours. [. . . ]