User manual UNIDEN EXP9200

[. . . ] Table of Contents Important Safety Instructions . 7 Installing the Base Unit on a Desk or Tabletop. 21 Using the EXP 9200 as a Room Monitor . 23 Important Electrical Considerations . [. . . ] This feature amplifies the earpiece audio through the Monitor Speaker on the Handset so you can monitor a call without having the phone next to your ear. The Handset microphone is turned off during monitoring, so you can consult another person in the room without the caller hearing you. Out of Range Indicator When the Handset is reaching the end of the EXP 9200's range limit, a beep sounds in the earphone every four seconds. If the Handset goes farther out of range, the warning beeps every 1. 5 seconds. You must go back into range within 20 seconds or the call will be dropped. 15 Keypad Lights The Handset Keypad Lights flash when a call is received and remain lit for 10 seconds. Also, pressing any button turns the Keypad Lights on for 10 seconds. The Base Unit rings (two rings for Line 1, three rings for Line 2), and the corresponding green Line LED flashes. Press the flashing Line Button or the SP. Note: If both Line 1 and Line 2 are ringing, press SP. The Handset rings (two rings for Line 1, three rings for line 2), and the corresponding green Line LED and Keypad Lights flash. If the Handset is not in the Base Unit, press the flashing Line Button, or TALK to answer the call. --OR-- If the Handset is in the Base Unit, the AutoTalk feature allows you to answer the call by simply picking up the Handset and beginning your conversation. Note: If both Line 1 and Line 2 are ringing, press TALK or lift the Handset from the Base Unit to answer the last line used. When you finish the call, place the Handset back on the Base Unit. AutoStandby automatically hangs up the phone. There is no need to press TALK to hang up. --OR-- If the Handset is away from the Base Unit, press TALK to hang up the phone. Making a Call from the Base Unit 1. PHONE is pressed, the EXP 9200 returns to the last line used. When the LINE 1 or LINE 2 LED glows steadily and you hear a dial tone, dial the number you are calling by pressing the numbers on the keypad or using one of the memory features (See "Using Your EXP 9200 Memory. ") 3. Note: When TALK is pressed, the EXP 9200 returns to the last line used. The TALK LED flashes and there is a slight delay while the Spread Spectrum Technology in your EXP 9200 sets up a digital link between the Handset and the Base Unit. When the LINE 1 or LINE 2 LED glows steadily and you hear a dial tone, dial the number you are calling by pressing the numbers on the keypad or use one of the memory features. [. . . ] 24 Specifications General Frequency Control Modulation Operating Temperature Base Unit Receive/Transmit Frequency Power Requirements Size Weight Handset Receive/Transmit Frequency Power Requirements Size Weight Battery : 903. 087 to 925. 6131 MHz (23 Channels) : Rechargeable Ni-Cd Battery Pack 3 : 2 3 in. H with antenna 8 8 60mm W X 55mm D X 245mm H with antenna The EXP 9200 complies with FCC parts 15 & 68 : Crystal controlled transmission : Spread Spectrum System : -10° to 50° C : 903. 087 to 925. 6131 MHz (23 Channels) : 120V AC, 60 Hz 5 : 6 3 in. H 4 8 170 mm W X 22 mm D X 80 mm H : Approx. with battery : BP-9100 Capacity Talk Mode Standby Mode Specifications shown are typical and subject to change without notice. 25 ® EXP 9200 Cordless Telephone Operating Guide PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. [. . . ]