User manual UNIDEN EXV958

[. . . ] THE EXV 958 VoiceDial The World's First Cordless ITAD Integrated with Voice OWNER'S MANUAL · ·· ·· ·· · · Recognition Technology! ® Color profile: Disabled Composite Default screen CONTENTS Introduction . 5 · Installing the Handset Battery Pack . 6 · Setting the Pulse/tone Switch . 8 · Automatic Digital Code Security. [. . . ] 7) Then press store. VO I C E D I A L P R O G R A M M I N G 8) You will hear: Then, you will hear a confirmation beep. 15 I:. . . Backup of exv958final. vp Fri Jun 19 21:14:39 1998 Color profile: Disabled Composite Default screen TIP When the voice prompt says "Replace memory [location number]. Say yes or no, " if you don't say anything within 6 seconds, you will hear "louder please. " If you still don't respond, the handset beeps and the programming procedure cancels. ERASING A STORED NUMBER 1) Remove the handset from the base. Enter the 2-digit memory location. " 3) Enter the 2-digit memory location number that you want to erase. You will hear: "Replace memory zero one?Say yes or no. " 4) Say "Yes. " This erases the memory location. 5) Press store. DIALING A STORED NUMBER 1) Remove the handset from the base. voice/mem speaker 2) Press voice/mem. 3) You will hear: Say the location name or enter the 2-digit location number (01-30). 4) The number will automatically dial. CLIP 16 I:. . . exv958final. vp Fri Jun 19 21:16:50 1998 Color profile: Disabled Composite Default screen REVIEWING NUMBERS IN MEMORY 1) Press rev. The talk LED flashes. 2) You will hear: For example: You've programmed John Smith's phone number, 555-5555, into memory location 01. You will hear: HINT When you are ready to talk on the phone, press speaker to use the handset speaker phone. 3) To dial the announced number, simply press talk before you hear the last digit. 4) To hear the number in the next memory location, press . Or, to hear the number in the previous location, press 5) If you don't press or , you will hear all your programmed memory locations one at a time from the lowest to the highest memory location number. If you want to dial an announced number, press talk before you hear the last digit. . DIAL ANNOUNCE ON/OFF VO I C E D I A L P R O G R A M M I N G TIP For faster dialing, you can turn off the "Dialing [number]" announcement. w To turn the "dialing" announcement off Press store and then . The dialing announcement is off. w To turn the "dialing" announcement on Press store and then . The dialing announcement is on. 17 I:. . . exv958final. vp Fri Jun 19 20:20:27 1998 Color profile: Disabled Composite Default screen THE INTEGRATED ANSWERING DEVICE USING ANSWER Using the Integrated Answer Device THE INTEGRATED ANSWERING DEVICE The EXV 958 has a built-in answering system that answers and records incoming calls. You can also use your answering system to record a conversation, leave a memo message for others who use the phone, or to announce a special message to callers when you're away from your phone. FEATURES · · · · · · Digital Tapeless Recording 15 minutes of Recording Time Call Screening Selectable Outgoing Messages Time and Day Stamp Toll Saver SETTING UP 18 I:. . . exv958final. vp Fri Jun 19 20:20:30 1998 Digital Tapeless Recording allows you to quickly review, save, or delete the messages you choose. You'll never have to worry about a tape wearing out, jamming, or resetting improperly. The Integrated Answering System is easy and convenient to use, but please read through all of the instructions carefully before attempting to use it. TURNING THE ANSWERING SYSTEM ON/OFF 1) To turn the answering system on, press answer. A tone sounds and the current outgoing message plays on the base speaker. A second tone sounds after the outgoing message. The message counter LED turns on to indicate that the unit is ready to answer calls. 2) To turn the answering system off, press answer again. A tone sounds followed by the announcement "Answer off" and the message counter LED turns off. Color profile: Disabled Composite Default screen USING SETTING THE CLOCK The clock on the EXV 958 Answering System starts when power is applied to the base. [. . . ] · The handset may be too far away from the base. · Place the base away from noise sources. · The digital security code may be erased. · Make certain that the ringer on/off switch is in the RING ON position. [. . . ]