User manual UNIDEN GPS352

[. . . ] Some local, state, and federal regulations may prohibit the use of this detection device. Please check with authorities regarding the use of this device before operating it. Since the GPS352 determines its positioning from GPS (Global Positioning System), a navigational positioning system whose operation is controlled by the Department of Defense (USA), its performance may be limited by the operational conditions controlled. Operation Notice Safety Warning Systems You have purchased the newest technology designed for Radar, Laser and Safety Warning System detection and alert. You should be aware that Safety Warning transmitters (the device that alerts your detector for safety warning alerts) will be available for use throughout the United States. [. . . ] · The power cord does not block the antenna area. When installing the power cord, make sure that: Your unit also comes with ten power cord mounting clips. You can use these clips to attach the power cord to the window frame or other parts of the vehicle, keeping it neat and out of the way. Use the double-sided foam tape squares to attach each clip. Slip the power cord into the clip to hold it securely in place. 11 Replacing the Fuse The cigarette lighter plug contains a 1-ampere fuse to protect it from power surges. To replace the fuse, unscrew the top of the plug. 2. Remove the fuse and replace it with the same type. 3. To replace the top, push in on the two metal contacts and twist into place. Note: Your GPS352 comes with an extra fuse. 12 Operation You are now ready to enjoy the convenience and security of your GPS352. Please read this section of the Operating Guide carefully to familiarize yourself with the basic operation of this unit. Power On Turn the Volume Control knob to turn power on. The GPS352 is set to Demo mode and it performs a series of self-tests on its radar detection displays and alert tones. After the self-tests of X, K, Ka, Laser, L2, L3, VG2, and SWS, the display shows "Welcome to Uniden GPS352" scrolling as follows. RED RED When all the characters on the display have been scrolled through after the self-tests, the detector sets the modes that were used last. The display will then scroll, (searching for satellite). This will indicate that the GPS352 is trying to acquire satellite information. The upper LED lights red during Demo mode and turns to green when the detector receives signals from GPS satellites. Choosing "OFF" will eliminate the direction arrow showing the way to your destination. 2. Mark Loc (Mark Location) To enter into this mode, select "Mark Loc" using the L or M button, and press the SELECT/TRAP button. At this mode, you can register the latitude and longitude data for 7 specific points as shown in fig. Select the point you want to register using the L or M button, and press the SELECT/TRAP button. After "Marked" indication, the display returns to the Normal mode. "Menu Mode" [SELECT/TRAP]SW [EXIT/ALERT]SW GREEN [SELECT/TRAP]SW GREEN [ ]SW GREEN [ ]SW GREEN [ ]SW GREEN [ ]SW [ ]SW GREEN [ ]SW GREEN [ ]SW GREEN [ ]SW [ ]SW [ ]SW [ ]SW [ ]SW [ ]SW [ ]SW [ ]SW [ ]SW Note: If the Status Indicator is red, you will not be able to program your location. Move to a different location in order to receive better satellite reception. When you approach the location, the detector sounds alert tones in 3 levels as follows. Distance (Radius/Mile) 1. 0 0. 5 0. 1 Alert Tone Time 3 sec 3 sec 3 sec Alert Display Time 3 sec 3 sec 3 sec Level 1 Level 2 Level 3 17 3. Speeds Select "Speeds" and press the SELECT/ TRAP button. In this mode, the detector displays the maximum or average speed data stored in the GPS module. "Menu Mode" [SELECT/TRAP]SW [EXIT/ALERT]SW GREEN [SELECT/TRAP]SW GREEN [ ]SW GREEN [ ]SW [ ]SW Use the L or M keys [ ]SW [ ]SW [ ]SW to toggle between the GREEN maximum and average display. To delete the [SELECT/TRAP]SW GREEN data, select "Delete?" and press the SELECT/ 2sec later TRAP button. [. . . ] · Relocate the unit clear of the window tint. Inaccurate or erratic · Loose power cord. Beeps over bumps or · Check that the power cord is rough road. · Clean cigarette lighter socket. [. . . ]