User manual UNIDEN MINI200

[. . . ] CONTENTS OF YOUR OWNER'S MANUAL Safety Information . 4 · · · · · · · · · Setting Up Your Phone . 8 CONTENTS i Memory Programming . 11 · · · · · · Menus - Customizing Your Phone . [. . . ] NOTE: This overrides the keyguard. w PIN Calling To protect from unauthorized use of some cellular or automated systems, you can use a personal identification number (PIN). The PIN must be programmed; see page 26. If you enter a service area that does not require a PIN, set the PIN feature to off. w Inserting a Pause If you need a pause to separate groups of numbers during dialing, press and hold . Entering another pause increases the length of the pause between numbers. ENDING A CALL When you finish your call, press end. WHILE CALLING w Adjusting the Earpiece Volume During a conversation, press either v or w. You can do this through the volume menu (page 14). 8 w Using the Scratch Pad Use the scratch pad to record a phone number during a call. Then you can dial that number from the scratch pad or enter it into a memory location. 1) During a call, enter the number with the keypad. 2) When you are finished with your call, press end. 3) To dial the number in the scratch pad, press send. w Mute · If you want to mute the microphone so the caller cannot hear, press menu and again. w Monitor . · To turn the microphone back on, press menu and NOTE Since the microphone (on the front) is disabled during monitor, the caller can't hear you. During monitor, you hear the conversation from the speaker on the back. Use this feature for calling a bank or similar automated answering system. · To enable the monitor feature, press · To disable the monitor feature, press w Transmitting DTMF Signal(s) (monitor). (monitor). DTMF (dual tone multi-frequency) tones are transmitted from your phone when you press a digit key during a call. w Flash Signal (Signaling Tone) CALLING When you press send during a call, it generates a flash signal (signaling tone). 9 MEMORY PROGR AMMING Memor y Programming STORING NUMBERS AND NAMES The MiniCel has 50 memory locations (01 through 50). You can also store a 10-digit description or name to identify the phone number. There are three sources to enter numbers into memory: the scratch pad, entered in standby or the recall numbers list. 1) With the number in the display, HINT To exit memory mode, press end or clear. press and hold mem for one second. 2) Enter the location number where you want to store the number. Example: location 01 To search for an empty location, press either v or w. If all the locations are full, the MEMORY FULL message appears and an error tone sounds. If the location is occupied, you will be prompted: Example: you want to replace the number in memory, press v for yes. MEMORY 10 PROGRAMMING FOR YOUR PHONE 3) If you want, you can enter a 10-character name with the keypad. Example: HOME 4) To store the name or to finish, press mem. You will see: After two seconds, the display returns to standby. CHECKING MEMORY STATUS From the standby display, press mem three times. To return to the standby display, press either mem, end or clear. MEMORY CALLING STORED NUMBERS TIP Put the phone numbers that you call the most in the first nine memory locations. Then use speed dial to call them. w Speed Dial Press mem, the two-digit memory location number (01-50) and send. [. . . ] 7) Press menu. MENUS · If you choose SHOW TIME you will see: Press menu to return to standby. · If you choose RESET, you will be prompted for your password. When you enter the password, you will see RESET. In two seconds, the display returns to standby. 29 SERVICE SETTINGS MENU w Phone Line Menu HINT To move to a menu, use either the v (up) or w (down) key. 1) To go to the service settings menu from standby, press menu. 2) Press w five times. 3) Press menu. HINT To exit menu mode, press end or clear. 4) Press menu again. 5) Use the w or v keys to choose between LINE 1 or LINE 2. You will see: In two seconds, the display returns to standby. TIP Contact your service provider to set up line 1 and line 2. 30 w Network Menu HINT To move to a menu, use either the v (up) or w (down) key. 1) To go to the service settings menu from standby, press menu. [. . . ]