User manual UNIDEN TRU341

[. . . ] O W N E R'S MANUAL T R U 3 41 Contents Introduction 1 Using Your Phone 10 Features Included with Your TRU 341 Phone Controls and Functions Installation 1 3 4 5 · Charging the Battery Pack Charging the Handset Battery use time (per charge) Low Battery Indicator Cleaning the Battery Contacts · Selecting a Location Setting Up Your Phone 5 5 6 6 6 7 8 · Connect the Base Unit · Setting the Dial Mode Switch · Adjusting Ringer/Volume Controls Ringer Tone and Volume Setting the Handset Earpiece Volume 8 8 9 9 9 · · · · · · · · · · · · · Making and Receiving Calls Storing a Number in Memory Entering a Pause in Memory Dialing Storing Mixed Tone/Pulse Numbers Dialing a Stored Number Chain Dialing Erasing a Stored Number Mute Replacing a Stored Number Selecting a Dif ferent Channel Using the Flash Button Using the Page/Find Feature Traveling Out of Range 10 10 11 11 12 12 12 13 13 13 14 14 14 15 16 Troubleshooting Installing the Beltclip · To Attach the Beltclip · To Remove the Beltclip Headset Installation General Information 16 16 16 17 INTRODUCTION Introduction The Uniden ® 2. 4 GHz cordless phones are designed and engineered to exacting standards for reliability, long life, and outstanding performance. Digital Spread Spectrum Technology utilizes a "wider frequency band" vs. a "single narrow band" used in standard digital transmissions. The 2. 4 GHz frequency range was recently released to commercial communications. [. . . ] While the phone is not in use, press volume . 2. The phone has two ringer tones, each with two volume levels. Press volume again until you hear the ringer tone and volume level you want. w Setting the Handset Earpiece Volume 1. While you are on a call, press volume . 2. The phone has four receiver volume levels; Low, Medium, High, and Maximum. Press volume again until you hear the volume level you want. When you hang up, the phone keeps the last volume setting selected. SETTING UP YOUR PHONE [9 ] Using Your Phone Making and Receiving Calls Handset on Base When the phone rings, remove the handset Answer call from the base. Remove the handset from the base and press talk . The t a l k / b a t t e r y l o w LED lights. Return handset to the base, Hang up (AutoStandby) or press talk . Remove the handset from the base and press talk . Press r e d i a l to dial the last number dialed. The t a l k / b a t t e r y l o w LED lights. Press r e d i a l to dial the last number dialed. · You have 20 seconds after pressing m e m o r y to enter the number you wish to store. · Write down stored numbers on the supplied memo sticker. Storing a Number in Memory Your TRU341 phone has 10 memory locations for storing important telephone numbers. Remove the handset from the base and press memory . The t a l k / b a t t e r y l o w LED flashes. Enter the phone number you want to store (up to 20 digits). Press memory and enter a number (0-9) on the keypad for the memor y location you want to use. You hear a long beep and the t a l k / b a t t e r y l o w LED goes out indicating the number has been stored successfully. If you select any keys other than 0-9, the handset will beep rapidly and no number will be stored. [ 10 ] U S I N G Y O U R PHONE Entering a Pause in Memory Dialing If you would like to use a phone number stored in memor y to access voice mail, for example, you can store a pause in the phone number sequence. To use this function, follow steps 1 and 2 in "Storing a Number in Memor y " , then press the pause button on the handset to place a pause in the phone number sequence. [. . . ] · Disconnect the AC adapter for a few minutes, then reconnect it. · Reset the security code by placing the handset back on the base for a few seconds. The s t a t u s LED will blink indicating that the phone has been reset. Handset doesn´t ring · The nickel-cadmium batter y pack may be weak. [. . . ]