User manual UNIDEN TRU8880-2

[. . . ] TRU 8880 SERIES OWNER'S MANUAL WELCOME/FEATURES/TERMINOLOGY CONTROLS AND FUNCTIONS DISPLAY AND ICONS SOFT KEY FUNCTION GETTING STARTED Setting up the Phone Mounting the Base Unit on a Wall Expanding Your Phone Connecting the Charger Register the Handset Main Menu Options Setting Menu Options Contents 2 4 6 8 9 CALLER ID Caller ID and CIDCW (Caller ID on Call Waiting) Viewing the Caller ID List Deleting a Caller ID Message Using the Caller ID Message List Call Waiting Deluxe Features 50 50 51 52 53 55 9 12 14 14 15 16 17 THE INTEGRATED ANSWERING DEVICE The Integrated Telephone Answering Device Turning the Answering System On/Off Setting up your Answering System Using your Answering System Remote Operation 56 56 57 58 66 70 MULTI-HANDSET FEATURES Multi-Handset Features Using the DirectLink Mode Intercom/Call Transfer Feature 74 74 74 75 BASICS Making and Receiving Calls Call Waiting Placing a Call on Hold Redialing a Call Adjusting the Ringer, and Earpiece and Speaker Volume Muting the Ringer Mute Microphone Tone Dialing Switch-over Travelling Out of Range Privacy Mode Conferencing 33 33 35 35 36 37 38 39 39 40 40 41 ADDITIONAL INFORMATION Changing the Digital Security Code Installing the Beltclip Headset Installation Note on Power Sources General Information 78 78 78 78 79 81 TROUBLESHOOTING Troubleshooting Liquid Damage 82 82 85 PHONEBOOK 42 Phonebook (Storing Phone Numbers, Names, Distinctive Rings and Speed Dial) 42 Chain Dialing 43 Steps for Entering Names and Special Characters 44 Viewing the Phonebook 46 Making Calls Using the Phonebook 47 Speed Dialing 47 Editing or Erasing a Stored Name, Phone Number, Distinctive Ring and Speed Dial 48 Copying Phonebook Locations 49 www. uniden. com PRECAUTIONS & WARRANTY I. C. NOTICE MEMORY LIST INDEX REMOTE OPERATION CARD MAIN MENU FLOW CHART 86 88 89 91 92 94 [1] Welcome Congratulations on your purchase of this Uniden Digital Expandable Cordless Telephone System!This unit is different from conventional cordless telephones. When the base unit is connected to AC power and a telephone line, it can support up to 10 handsets. [. . . ] A confirmation tone sounds, the day and time you set are announced for your review. T H E I N T E GR AT E D ANSWERING DEVICE [60] THE INTEGRATED ANSWERING DEVICE www. uniden. com Setting a PIN code To play your messages from a remote location, you will need to enter a two-digit Personal Identification Number (PIN) code. To select a PIN code, perform the following steps: 1) Press clock/menu twice. The current PIN code appears on the base and it is announced. 2) Press skip/select or repeat/select until the desired number appears. Press and hold skip/select or repeat/select to quickly scroll through the numbers on the display. A confirmation tone sounds, the system announces the new PIN code. T H E I N T E GR AT E D ANSWERING DEVICE Setting the ring time The ring time setting allows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after two, four, or six rings. Setting "TS" (Toll Saver), the answering system picks up after two rings if you have new messages, and after four rings if there are none. This way, if you make a long distance call to check your messages, you can hang up after the second ring to avoid billing charges. The current ring time setting (2, 4, 6, (Toll saver)) appears on the base and it is announced. 2) Press skip/select or repeat/select until the desired ring time appears. 3) Press set to select the new ring time. A confirmation tone sounds, the system announces the new ring time. www. uniden. com THE INTEGRATED ANSWERING DEVICE [61] Selecting the message record time You have three record time options. The options "1 minute" or "4 minutes" set the duration for recording the incoming messages. "Announce only" answers the call with the preset greeting or your personal greeting but prevents the caller from leaving a message. The current recording time (1 minute, 4 minutes, (Announce only)) appears on the base and it is announced. 2) Press skip/select or repeat/select until the desired message record time appears. 3) Press set to select the new recording time. A confirmation tone sounds, the system announces the new record time. T H E I N T E GR AT E D ANSWERING DEVICE Announce only feature The Announce only feature plays a pre-recorded outgoing message or your own personal outgoing message, but it will not allow the caller to leave a message. To set "Announce only", follow the steps in "Selecting the message record time". To choose between the pre-recorded message or your own personal greeting, press greeting, when the outgoing message is played. Press greeting to select the greeting of your choice. [. . . ] Call your phone and let it ring 10 times until you hear a beep. Press 0 then 5 to stop the announcement. Press 0 then 6 to turn the answering system on. CUT CUT REMOTE OPERATION CARD REMOTE OPERATION CARD Remote access away from home 1. Call your phone number from a touch-tone phone. [. . . ]