User manual UNIDEN XC3545

[. . . ] Table of Contents Important Safety Instructions . 21 Installing the Handset Battery Pack . 32 Changing Channels, Hold, Mute, and Flash . 39 Storing a Tone/Pulse Number With a Pulse Dial System. [. . . ] Return the Handset to the Base Unit for charging. T During a Call button operates. In Standby Mode None of the buttons will operate. The Handset TALK/BATT LOW LED flashes once every 3 seconds. Return the Handset to the Base Unit for charging. Note: Allow 15 to 20 hours without any interruption for the Handset to fully recharge. 26 Setting the Tone/Pulse Switch Be sure the TONE/PULSE switch is in the TONE position. TONE-PULSE Note: Most phone systems are Tone dialing. Check with your local phone company if you are not sure whether your system is Tone or Pulse dialing. Adjusting Ringer/Volume Controls The Handset and Base of the :+!#"# have controls to adjust their volumes. Handset Volume Controls To adjust the ringer volume of your Handset, press when the phone is not in use. L OPER 0 TONE MEM 1 2 3 FLASH VOLUME INT'C R. TONE R. VOL RDL/P Handset Ringer Volume Control You can also select one of two different ringer tones for the Handset. Press to select a different ringer tone when the phone is not in use. O OPER 0 TONE MEM 1 2 3 FLASH VOLUME INT'C R. TONE R. VOL RDL/P Handset Ringer Tone Select Button 27 To adjust the receiver volume, press while you are on a call. V OPER 0 TONE MEM 1 2 3 FLASH VOLUME INT'C R. TONE R. VOL RDL/P Handset Receiver Volume Select Button Base Volume Controls To adjust the Base Unit ringer volume, move the RING-OFF LO HI switch to the desired setting. RING-OFF LO HI To adjust the Base speaker volume, slide the VOLUME control to the desired setting. VOLUME VOLUME VOLUME 28 Automatic Digital Code Security Many cordless telephones operate similarly and on the same frequency. Without digital code security, another Handset could make calls using your Base Unit and telephone line. To avoid unauthorized calls on your phone, a Digital Code feature was added to the:+!#"#. This Digital Code is shared only between the Handset and Base Unit. The Code is set automatically when you first use the phone. To reset the Digital Code, be sure the Handset is on the Base, then: 1. Press on the Base Unit. Note: The phone begins ringing when is pressed. 2. Remove the Handset from the Base Unit, and then set it down again. (The ringing will stop. ) I I 29 3. The CHARGE LED will blink to indicate that the Digital Security Code is set to one of the more than 65, 000 codes. ABC IN USE CHARGE DEF 1 GHI 2 JKL 3 MNO RDL/P 1 4 FLASH 2 PRS 5 TUV 6 WXY 7 MEM 3 TONE 8 OPER 9 * Extend·A·Phone HQ SERIES 0 SPEAKER MUTE INT'COM PAGE / FIND If the Base Unit loses power while the Handset is off the Base, the Digital Code may be erased. When this happens, the Handset will not function. To establish communication between the Handset and Base Unit: 1. Remove the Handset from the Base Unit (if it is on the Base Unit). 30 2. Restore power to the Base Unit, and place the Handset back on the Base Unit. The CHARGE LED will blink to indicate that the Digital Security Code is set. ABC IN USE CHARGE DEF 3. 1 GHI 2 JKL 3 MNO RDL/P 1 4 FLASH 2 PRS 5 TUV 6 WXY 7 MEM 3 TONE 8 OPER 9 * Extend·A·Phone HQ SERIES 0 SPEAKER MUTE INT'COM PAGE / FIND 31 Using your XC3545 The :+!#"# has dual keypads: one in the Handset, and one on the Base Unit. This is like having two phones because most operations can be performed using either the Handset or the Base Units. Making and Receiving Calls The following features of your :+!#"# phone are different depending on the Handset's location when you make or receive a call. HANDSET BASE UNIT ON BASE UNIT ANSWER CALL OFF BASE UNIT Pick up Handset (AutoTalk) PressT 1) PressK The speaker LED lights. Note: A call causes the IN USE LED to blink. 1) PressK 2) Listen for dial tone 3) Dial number MAKE CALL 1) Pick up Handset 2) PressT 3) Listen for dial tone 4) Dial number 1) PressT 2) Listen for dial tone 3) Dial number HANG UP PressT -- OR -- Return Handset to Base (AutoStandby) 1) Pick up Handset 2) PressT 3) Listen for dial tone 4) PressR 1) PressT 2) Listen for dial tone 3) PressR PressK The speaker LED goes off. REDIAL Note: Sometimes when you press to hang up the phone, you may get an error tone and the phone will not disconnect. If this happens, place the Handset on the Base Unit or press again while holding the Handset close to the Base Unit. 32 TT 1) PressK The speaker LED lights. 2) Listen for dial tone 3) PressR Changing Channels, Hold, Mute, and Flash To change channels, place a call on hold, mute a call, or access call waiting while on the phone, follow these steps: CHANGING CHANNELS Press Note: Change channels to help eliminate background noise. [. . . ] Crystal controlled transmission FM ­ 10° to 50° C Specifications, Features, and availability of Optional Accessories are all subject to change without prior notice. 54 ® XC3545 Cordless Telephone D UDZZ01323ZZ Operating Guide PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture. RECHARGEABLE NICKEL-CADMIUM BATTERY WARNING This equipment contains a Rechargeable Nickel-Cadmium Battery. Cadmium is a chemical known to the State of California to cause cancer. The Rechargeable Nickel-Cadmium Battery contained in this equipment may explode if disposed of in a fire. [. . . ]