User manual UNIDEN XC645

[. . . ] CONTENTS Important Safety Instructions . 31 Changing Channels, Mute, Flash, and Page/Find . 43 1 Important Safety Instructions When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons: 1. Follow all warnings and instructions marked on the product. [. . . ] The steps below describe how to remove and replace the retainer so that the tab faces up. Push up on the Handset Retainer on the Base Unit, and slide the tab out. 25 CHANNEL 2. Flip the retainer over so the tab faces up. 25 CHANNEL 18 3. Put the retainer back into its slot on the Base Unit. 25 CHANNEL 4. Push down on the Handset Retainer until it snaps into place. 25 CHANNEL 19 Setting Up Your Phone Extending the Antenna Before using your phone, be sure to raise the antenna to the vertical position. volume Installing the Handset Battery Pack 1. Press in on the Battery Cover Release. charge 20 2. Slide the battery compartment cover down. 3. Align the plastic connector of the Nickel-Cadmium battery pack with its socket and plug it in. Note: The black lead will be on the left when the plug is properly aligned. 4. Place the battery pack inside the battery compartment, and slide the battery cover back on. Note: The built-in Memory Backup feature allows up to 3 minutes to disconnect the old battery pack and install a new one without losing any numbers stored in memory. 21 Cleaning the Battery Contacts To maintain a good charge, it is important to clean all charging contacts on the Handset and Base Unit about once a month. Use a pencil eraser or other contact cleaner. Do not use any liquids or solvents. 25 CHANNEL ULTRACLEAR PLUS talk flash/rdl talk batt low speaker 1 4 7 ghi 2 5 8 tone abc 3 6 9 def jkl mno pqrs tuv wxyz 1 4 ghi 2 abc 5 jkl 8 tuv tone 3 def 6 mno 9 wxyz D mem 0 r. tone pause oper r. vol chan 7 pqrs mem pause volume 0 page/find oper redial # flash mute Extend"A"Phone Contacts Contacts 22 Charging the Battery Pack Initial Battery Charging The rechargeable Nickel-Cadmium battery pack must be fully charged before using your phone for the first time. We recommend that the battery pack charge for approximately 15-20 hours, without interruption, before plugging the phone line into your new phone. Place the Handset on the Base Unit. --or-- Hang the Handset on the cradle when the phone is mounted on a wall. Note: Make sure to change the Handset Retainer before hanging up the phone. 23 volume 2. Make sure the charge LED lights. If the LED doesn't light, check to see that the AC Adapter is plugged in, and that the Handset is making good contact with the Base Unit charging contacts. 25 CHANNEL charge 1 4 ghi 7 pqrs mem Continuous Battery Charging For the best battery performance, return the Handset to the Base Unit at the end of the day. This keeps the battery fully charged and avoids the battery "memory effect. " 24 Low Battery Indicator When the Battery Pack in the Handset is very low and needs to be charged, the talk/batt low LED flashes. talk talk batt low flash/rdl 1 2abc 3def 6mno 4 ghi 5 jkl 7pqrs 8 tuv 9wxyz If the talk/batt low LED begins to flash, the phone is programmed to limit its functions to save power. The table below describes what to do to return your phone to normal operation. DURING A CALL IN STANDBY MODE Only the A button operates. The Handset beeps and the talk/batt low LED flashes once every 3 seconds. Complete your call as quickly as possible. Return the Handset to the Base Unit for charging. None of the buttons will operate. The Handset talk/batt low LED flashes once every 3 seconds. Return the Handset to the Base Unit for charging. Note: Allow 15 to 20 hours without any interruption for the Handset to fully recharge. 25 Setting the Pulse/Tone Switch Be sure the PULSE/TONE switch is in the TONE position. PULSE-TONE Note: Most phone systems are Tone dialing. Check with your local phone company if you are not sure whether your system is Tone or Pulse dialing. Adjusting Ringer/Volume Controls Handset Volume Controls To adjust the ringer volume of your Handset, press R when the phone is not in use. talk talk batt low flash/rdl 1 4 ghi 2abc 5 jkl 3def 6mno 7pqrs 8 tuv 9wxyz tone D 0 oper r. vol chan mem r. tone pause volume Handset Ringer Volume Control 26 You can also select one of two different ringer tones for the Handset. Press T to select a different ringer tone when the phone is not in use. talk flash/rdl talk batt low 1 4 ghi 7pqrs 2 abc 5 jkl 8 tuv tone 3def 6 mno 9 wxyz D mem 0 oper r. tone r. vol chan pause volume Handset Ringer Tone Select Button To adjust the receiver volume, press V while you are on a call. talk talk flash/rdl batt low 1 4 ghi 2abc 5 jkl 3def 6mno 7pqrs 8 tuv 9wxyz tone D 0 oper r. vol chan mem r. tone pause volume Handset Receiver Volume Control 27 Base Volume Controls To adjust the Base Unit ringer volume, move the RING VOL-OFF LO HI switch to the desired setting. RING VOL OFF-LO-HI To adjust the Base speaker volume, slide the VOLUME control to the desired setting. volume volume 28 Automatic Digital Code Security To avoid unauthorized calls on your phone, a Digital Code feature was added to all XC645 phones. This Digital Code is shared only between the Handset and Base Unit. The Code is set automatically when you first use the phone. To change the Digital Code, be sure the Handset is on the Base, then: 1. Press page/find on the Base Unit. 2. After the Handset stops beeping, remove it from the Base Unit. 29 3. Wait 5 seconds then place the Handset on the Base Unit. The charge LED will blink quickly, indicating that the Code has changed. If the Base Unit loses power while the Handset is off the Base, the Digital Code may be erased. When this happens, the Handset will not function. [. . . ] Flash F /Redial 1 2 talk flash/rdl talk batt low 3 1 9 3def 6 mno 9 wxyz 2 abc 5 jkl 8 tuv tone F C 4 5 6 7 8 4 ghi 7pqrs 10. Ringer Volume R/ Volume V D mem 0oper r. tone r. vol chan pause volume 10 11 Base Unit Controls and Keys 1 234 5 6 7 8 25 CHANNEL ULTRACLEAR PLUS 16 speaker 1 4 ghi 7 pqrs tone mem pause 2 abc 5 jkl 8 tuv 0 oper redial mute page/find 3 def 6 mno 9 wxyz volume # flash Extend"A"Phone 9 11 13 15 10 12 14 1. Base Ringer Switch Pulse/Tone Switch DC Power Jack Telephone Line Jack Handset Retainer Speaker Button with LED Built-in Speaker Numeric Keypad 9. Tone Button Memory Button M Page/Find Button Pause Button P Redial Button Mute Button with LED Flash Button Speaker Volume Control PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. [. . . ]