User manual UNIVERSAL REMOTE CONTROL ATLAS 4-DEVICE

[. . . ] Atlas Manual rev2 12/27/02 11:07 AM Page 1 ATLAS CABLE 4-DEVICE Universal Remote Control User's Guide Atlas Manual rev2 12/27/02 11:07 AM Page 2 TABLE OF CONTENTS Introduction . 23 To De-Activate Channel Control Lock . 23 To Re-Activate Channel Control Lock . 26 Example ­ Programming A Favorite Channel . [. . . ] For example, to find out which code is operating your TV: 1. Then press and hold SETUP until the TV key blinks twice, then release SETUP. The TV key will blink twice. 2. 3. To view the code for the first digit, press 1 once. Wait 3 seconds and count the number of times the TV key blinks (e. g. , 3 blinks = 3) and write down the number in the leftmost TV Code box (see below). NOTE: If a code digit is "0", the selected mode key will not blink. 4. Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. Finish writing down the code in the TV Code boxes below. To check for other device codes, repeat steps 1 through 4, but substitute the appropriate key (i. e. , AUD, VCR, or CABLE) for the (Audio, VCR, or Cable) device you are checking. Write down the codes in the appropriate boxes below. AUD Code Audio Device ____________________ VCR Code 5. TV Code CABLE Code 21 Atlas Manual rev2 12/27/02 11:07 AM Page 22 PROGRAMMING ID LOCK The Atlas Universal Remote Control is preprogrammed and locked at the factory to operate a Scientific Atlanta cable converter. However, if you have another brand or model of cable converter and interactive service that you would like to control, then you'll need to perform the following steps to unlock the cable ID Lock, enter in a new manufacturer's code, and lock the ID Lock again. Then press and hold SETUP until the CBL key blinks twice, then release SETUP. Perform the instructions in Programming Device Control on page 8 to program device control for the desired cable converter and interactive service. Upon completion, perform the remaining steps (5 and 6 on this page) to again lock the ID lock. Then press and hold SETUP until the CBL key blinks twice, then release SETUP. The CBL key will blink twice. 3. 4. 5. 6. 22 Atlas Manual rev2 12/27/02 11:07 AM Page 23 PROGRAMMING CHANNEL CONTROL LOCK By default, the remote control's channel-control capabilities are locked to the cable converter. The affected keys* are 0 ~ 9, CH+, CH-, ENTER, and LAST. This will guarantee that you do not inadvertently change a channel on your TV or VCR. However, you can de-activate this feature to allow full access to these keys in the TV and VCR modes. *NOTE: This feature does not affect the AUD mode. To De-Activate Channel Control Lock: 1. Then press and hold SETUP until the CBL key blinks twice, then release SETUP. The CBL key will blink two times. 2. 3. Now, the remote control will provide TV and VCR channel-control capabilities while in the TV or VCR mode. To Re-Activate Channel Control Lock: 1. Then press and hold SETUP until the CBL key blinks twice, then release SETUP. The CBL key will blink two times. 2. 3. [. . . ] The last-selected device key will blink twice. Select a mode (e. g. , TV) where you want to globally lock the volume controls. The selected device key will blink twice. Now, when you press VOL+, VOL­, or MUTE, the volume of the selected device (e. g. , TV) can be controlled regardless of mode. 2. 3. 4. 29 Atlas Manual rev2 12/27/02 11:08 AM Page 30 TROUBLESHOOTING PROBLEM: Mode key does not blink when you press a key. [. . . ]