User manual UNIVERSAL REMOTE CONTROL AUTOMATOR URC-200

[. . . ] Owner's Manual Thank You! Thank you for purchasing the AutomatorTM URC-200 Pre-Programmed and Learning Remote Control. The Quick Setup DVD tutorial supplied with the Automator demonstrates the process of setting up and automating a home entertainment system. Watch the DVD first to familiarize yourself with the capabilities of the Automator and the setup process. This manual is designed to assist you step-by-step as you setup the Automator to replace all of your remote controls and automate your home entertainment system. URC-200 Owner's Manual © 2004 Universal Remote Control, Inc. [. . . ] If you don't want backlighting at all (this extends battery life), press the ON button that appears on the screen. Exit the setup mode by pressing the MAIN button. The FAV Button When you press the FAV button, the display changes to a list of your favorite TV channels. Each button can be set to instantly select the channel on your TV. There are eight pages of five favorite channel buttons for a total of 40. Simply touch the PAGE buttons to display the other favorite channels. To return to the last device you viewed, press MAIN once (a second press will take you to the MAIN menu). FAV Button Favorite Channel Buttons To setup your Favorite Channel buttons go to page 22. 15 The Automator Adjusting Contrast You can make the text darker by pressing both the MAIN and cursor UP buttons at the same time. To make the text appear lighter, press both the MAIN and cursor DOWN buttons at the same time. MAIN Button Cursor Up & Down Buttons Contrast set low. Contrast set high. Transmitting (Busy Signal) Icon When a command is being transmitted, an icon will appear in the top right corner of the display. It is a useful aid when setting up Macros and FAVs, since it flashes with every step of a sequence of commands. 16 URC-200 Advanced Setup After you've finished all your basic setup, you can choose to make operation easier by customizing the Automator just the way you want, using the Advanced Setup features described in this section. Editing Button Labels You can change the name of any of the display buttons (including Favorite Channels) by following these steps: 1 Press and hold both the MAIN and ENT (Enter) buttons for approximately three seconds. The top of the display will show "SETUP". You are in SETUP mode now. Note: You have 30 seconds to perform a step while you are in SETUP mode. If you don't press a button within that time, the Automator will time out and return to normal operation. 2 Press the EDIT button. EDIT Button 3 The display changes to the EDIT menu. TEXT Button 17 The Automator 4 The screen displays the list of devices and "EDIT" will appear at the top of the screen. Navigate to the device and page where there is a button label you want to EDIT, selecting between the FAV, MAIN, DEVICE; then using the PAGE button. Note : If you wish to change the name of a DEVICE button, press the Page Up button twice. The top of the display changes to MAIN, and you can navigate to MAIN page 1 or page 2 before going on to Step 5. 5 Press the button you wish to edit. The first character of your button label blinks. Blinking Character EDIT flashes at the bottom of the screen. LEFT Cursor button moves blinking character left. RIGHT Cursor button moves blinking character right. DOWN Cursor button deletes the currently blinking character. 18 URC-200 6 Change the character by using any of the number keys. Each press of the same number button selects the next character of that number's group, as shown below. A, B, C, 1 J, K, L, 4 S, T, U, 7 D, E, F, 2 M, N, O, 5 V, W, X, 8 G, H, I, 3 P, Q, R, 6 Y, Z, 9 7 8 Once the character you want appears, move to the next space by pressing the RIGHT cursor button. When you are finished editing the button, press the button you edited and "SAVED" will flash at the bottom of the display. To change any other button labels on the same device, press the next button, then repeat steps 6-8. [. . . ] If you install the Expander kit, the MRF-100 will receive the Automator's radio signals and translate them into the infrared commands that control your components. Note: The Automator's radio signals will not control components directly. You must have an Expander to receive the Automator's radio signals. Components that came with "no pointing" radio remote controls cannot be operated by the Automator unless the component can be switched to standard infrared control via its internal menus. Some remote control ceiling fans are radio only and cannot be operated by the Automator. 30 URC-200 The Automator sends radio signal to the Expander, which is a radio receiver. The Expander converts radio signals to standard infrared commands and sends them out via a built-in front blaster to components in the same cabinet space. Self-adhesive "flashers" (included in the Expander kit) affix to the front panels of your components. [. . . ]