User manual UNIVERSAL REMOTE CONTROL MRF100B POWERPACK

[. . . ] PowerBlasterTM OWNER'S MANUAL No More Pointing. . changing the way a remote control works! Universal Remote Control 500 Mamaroneck Avenue Harrison, NY 10528 Phone: 1-914-835-4484 FAX: 1-914-835-4532 www. universalremote. com MRF100B OWNER'S MANUAL No More Pointing. . changing the way a remote control works! MRF100B PowerBlasterTM 1 PowerBlasterTM Congratulations! Congratulations on purchasing Universal Remote Control's PowerBlasterTM MRF100B!When used in combination with PowerBlasterTM, a MasterControlTM RF series remote control (RF10, RF20, RF30) becomes an amazing remote control powerhouse that sends multi-directional RF (Radio Frequency) signals that pass through walls, doors and floors ­ both indoors and outdoors. [. . . ] The bottom of the LCD will blink "LOCKED" three times and then display "LOCKED". To Return to Normal Operation: Press the +10 and ENT (Enter) buttons simultaneously again for 3 seconds. The LCD will display the last use mode. STEP 1: Press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 seconds, until the word "SETUP" is displayed at the top of the LCD screen. This signals that you are now in setup mode. IMPORTANT:You now have 30 seconds to perform the next step while you are in SETUP mode. If you don't press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. STEP 3: Press the TEXT display button. The screen will display the list of Components and "EDIT" will appear at the top of the screen. STEP 4: Navigate to the Component and page where there is a button label you want to EDIT, selecting between the FAV, MAIN, COMPONENT display buttons; then using the PAGE button. NOTE: If you wish to change the name of a Component button, press the Page ( ) Up button twice. The top of the display will change to MAIN, and you can navigate to MAIN page 1 or page 2 before going on to Step 5. STEP 2: CUSTOMIZING BASIC SETUP Press the EDIT display button. The LCD display will change to the EDIT menu. 21 Customizing the LCD Screen 22 Customizing the LCD Screen STEP 5: Press the button you wish to edit. The first character space of your button label will start to blink. STEP 6: Change the character by using any of the number keys. Each press of the same number button selects the next character of that number's group, as shown in the diagram below. STEP 7: Once the character you want appears, move to the next space by pressing the Right cursor button. STEP 8: UP CURSOR Button deletes all text LEFT CURSOR Moves blinking character left When you are finished editing the button, press the button you edited and "SAVED" will flash at the bottom of the display. To change any other button labels on the same Component, press the next button, then repeat steps 6-8. If you wish to edit a button on another Component, press the MAIN button once, then repeat Steps 4-8. DOWN CURSOR deletes the currently blinking character CUSTOMIZING RIGHT CURSOR Moves blinking character right CUSTOMIZING BLINKING CHARACTER STEP 9: Once you've finished editing buttons, press the MAIN button four times to return to normal operation. 23 Favorite Channel Setup 24 Favorite Channel Setup This is one of RF20's most desirable features. Once it's set up, you can select up to 40 favorite channels with the press of a button - without the need to remember or type in a channel number. To access Favorite Channel listings, simply press the FAV button to display Page 1 of Favorite Channel listings. There are eight pages of Favorite Channels, with five Channels on each page, for a total of 40 Channels. Just use the PAGE ( ) ( ) buttons to locate the Channel you want to setup. Each Channel can be setup to be instantly selected with the press of one button. To setup a Favorite Channel button, follow these steps: Press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 seconds, until the word "SETUP" is displayed at the top of the LCD screen. This signals that you are now in setup mode. IMPORTANT: You now have 30 seconds to perform the next step while you are in SETUP mode. If you don't press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. Favorite Channel Setup STEP 3: STEP 1: STEP 2: Press the FAV display button. The top of the display will show "FAV". The bottom of the display will flash "SELECT" Use the PAGE ( ) ( ) buttons until you locate the name (i. e. , ABC, CBS, NBC) of the favorite channel you want to setup. STEP 5: Press either the TV, SAT or CABLE Component button (select the Component you use to enter channel numbers). STEP 6: STEP 4: Press the favorite channel display button you want to setup. The top of the screen will change to show the channel name. [. . . ] One of the best things about this is -- nothing has to be done to the RF20 for this feature to work. Every time you press a button on the RF20, it sends both a standard IR (Infrared Command) AND an RF (Radio Frequency) signal. If you install the PowerBlasterTM kit, it will automatically receive RF20's radio signals and translate them into the infrared commands that control your Components. NOTE: The RF20's radio signals will not control Components directly. You must have a PowerBlasterTM to receive the RF20's radio signals. [. . . ]