User manual UNIVERSAL REMOTE CONTROL MX-350

[. . . ] Owner's Manual Thank You! Thank you for purchasing the Osiris TM Pre-Programmed and Learning Remote Control. This manual is designed to assist you step-by-step as you setup the Osiris to replace all of your remote controls and automate your home entertainment system. Osiris Owner's Manual © 2004 Universal Remote Control, Inc. The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc. [. . . ] Each press adds half a second to the delay. 6 Press the LIGHT button to end your macro. A new screen displays three choices: SAVE Button SAVE -- If you are happy with your macro, press the SAVE button. UNDO -- The UNDO button lets you erase the last step. EXIT -- The EXIT button erases all the macro steps. 7 Press the MAIN button twice to return to normal operation. 20 Universal Remote Control, Inc. Favorite Channel Setup Imagine surfing all your favorite channels, without ever typing in a channel number. By simply setting up each of the favorite channel buttons, you can make TV, cable or satellite operation fun and easy. To setup a Favorite Channel button, follow these steps: 1 Enter SETUP mode by pressing and holding both MAIN and ENT for three seconds. Note: You have 30 seconds for each step, otherwise the Osiris will time out automatically. 2 Press the FAV display button. FAV Button The top of the display will show "FAV". The bottom of the display will flash "SELECT". 3 4 Use the Page buttons until you can see the name (i. e. , ABC, CBS, NBC) of the favorite channel you wish to setup. Press the favorite channel button you wish to setup. The top of the screen changes to show the channel name. The bottom of the screen displays "STEP0", indicating that you have not entered the channel number yet. Press either the TV, SAT or CABLE Device button (select the device you use to enter channel numbers). Press each of the number buttons for the channel. Note: Some brands of television require an ENT(Enter) command after the channel numbers. 5 6 21 The Osiris Note: If a number is repeated when setting the channel (for example, channel "33" or "522") it is usually best to set a half second delay in between the identical numbers by pressing the PAUSE button. Each press of the PAUSE button increases the delay by a half second. Use the PAUSE Button to set delays between steps, each press of the pause button increases the delay by a half second. 7 Press the LIGHT button after you enter the channel number. A new screen appears: SAVE Button To save the channel you entered, press the SAVE button. The UNDO button lets you erase the last entry. The EXIT button erases all entries for this button. 8 When you are finished setting up Favorite Channel buttons, press the MAIN button twice to return to normal operation. 22 Universal Remote Control, Inc. Hiding and Adding Pages Each of your Osiris Devices actually contains eight pages. However, only five pages are visible in the factory default setting. If you wish to use the hidden pages, you can ADD them. If you don't want to use some of the existing pages, you can HIDE them. You can add or hide pages on devices OR on your favorite channel pages using this simple process: Note: Be sure to program your Macros before you hide pages with a potential macro step in them. You can't access hidden pages during macro setup. However, after you finish Macro setup, you can hide pages without affecting operation of your macros. 1 Enter SETUP mode by pressing and holding both MAIN and ENT for three seconds. Note: You have 30 seconds for each step, otherwise the Osiris will time out automatically. 2 Press the EDIT button. EDIT Button 3 Press the PAGE button. PAGE Button "PAGE" appears at the top of the screen. 23 The Osiris 4 Navigate to any page, using the MAIN, DEVICE, FAV, and PAGE buttons. FAV Button PAGE Buttons MAIN Button DEVICE Buttons 5 When you select a page, the top of the screen indicates whether you want to "ADD?" or "HIDE?" the page displayed. [. . . ] Select DEVIC to change the blaster settings to just one of the devices in the Osiris. Then, go to Step 3. 3 The display changes to a list of the names of your devices. If you have two pages of devices, pressing either of the page buttons will display the other page. Select the device you would like to change IR/RF settings, then go to Step 4. [. . . ]