User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL 4605 WO CODE

[. . . ] Highlight or write down the codes and device you wish to program before moving on to step 2. CHECKING THE CODES If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment: For example, to find out which code is operating your TV: 1. Press and hold SET until the LED blinks twice, then release SET. To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e. g. , 3 blinks = 3) and write down the number. NOTE: If a code digit is "0", the LED will not blink. VCR back to VCR: DVD as 2nd TV key: SET - 9 - 9 - 2 - VCR - VCR SET - 9 - 9 - 2 - TV - DVD PROBLEM: VCR Mode Keys for Access 4: LED blinks when you press a key, but home entertainment component does not respond. ACCESS 4 UNIVERSAL REMOTE CONTROL SET POWER Press VCR, DVD, TV, or CBL/SAT once to select a home entertainment device to control. 1 4 2 5 8 0 MUTE DVD as 2nd CBL key: SET - 9 - 9 - 2 - CBL/SAT - DVD DVD as 2nd SAT key: SET - 9 - 9 - 2 - CBL/SAT - DVD DVD as 2nd VCR key: SET - 9 - 9 - 2 - VCR - DVD DVD back to DVD: SET - 9 - 9 - 2 - DVD - DVD SOLUTION: Make sure the remote control is aimed at your home entertainment device and is not farther than 15 feet away. PROBLEM: The unit does not control home entertainment devices or commands are not working properly. er. [. . . ] Make sure they can be operated with an infrared remote control. PROBLEM: TV/VCR combo does not respond properly. CH SLEEP SKIP REV REW PLAY REC PAUSE STOP FF ENTER TV/VID PROGRAMMING DEVICE CONTROL The One For All Access 4 remote control is preprogrammed at the factory to operate an RCA TV and VCR, a Motorola (GI) cable box, and a Toshiba DVD player. To control devices other than the default brands, perform the following steps; otherwise skip this section: NOTE: For TV/VCR Combo control, see the next section. EXIT MENU 4. Aim the remote control at the device and press POWER once. If the device does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (Play) key. 5. Repeat step 4 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. To check for codes of other devices, repeat steps 1 through 5, but substitute the appropriate device key for each device you are checking. As before, write down each fourdigit code. CHANGING VOLUME LOCK The One For All Access 4 is set to control the volume of your TV in the TV, VCR, CBL/SAT, and DVD modes. If you want the volume to be controlled by a mode other than TV (e. g. , CBL/SAT), change the Volume Lock as follows: SOLUTION: Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation. PROBLEM: Changing channels does not work properly. USER'S GUIDE VOL ­ VOL + Use VOL+ (or VOL-) to raise (or lower) the sound volume. Use CH+ (or CH -) to select the next higher (or lower) channel. To Change Volume Lock To Another Mode: 1. On the remote control, press and hold SET until the LED blinks twice, then release SET. Enter 9 - 9 - 3 and then press any mode key once (except TV). Now, whenever you press VOL+, VOL­, or MUTE, volume will be controlled by your mode choice. SKIP FWD CH INTRODUCTION The One For All Access 4 Universal Remote Control is designed to operate three (or four) home entertainment devices, depending on the model purchased (see Key Charts, Mode Keys on the right). The remote control requires two fresh AAA alkaline batteries and easy programming to control your devices. For best results, please read and perform all instructions listed here. Also, keep these instructions for future reference. CH 1. Turn on a device (e. g. , VCR) and, if applicable, insert media, (e. g. , cassette or disc). NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, to search for a code for your TV: 1. Press and hold SET until the LED blinks twice, then release SET. [. . . ] No part of this publication may be reproduced, transmitted, transcribed, stored in any retrieval system, or translated to any language, in any form or by any means, electronic, mechanical, magnetic, optical, manual, or otherwise, without the prior written permission of Universal Electronics Inc. One For All® Access 4 is compatibile for use in North America excluding Mexico. On the remote control, press and hold SET until the LED blinks twice, then release SET. Volume will again be controlled according to its default states. SOLUTION: Due to RCA design (19831987), only the original remote control will operate these functions. [. . . ]