User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL URC3220

[. . . ] WALRB3P manual booklet 5/2/06 3:13 PM Page 2 TABLE OF CONTENTS Introduction. 10 Programming The Power Key For The Master Power Macro . 12 Locking Volume Control To One Mode (Global Volume Lock). 12 Unlocking Volume Control For A Single Device (Individual Volume Unlock) . [. . . ] If the batteries are inserted correctly, the LED (red light) will blink. 5. Aim the remote control at the device and press POWER once. If it does not, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still doesn't work, try Searching For Your Code on next page. NOTE: If the device does not have a POWER key, press PLAY. 3. 4. 6. Repeat steps 1 through 5 for each device you want to control. For future reference, write down each working device code in the following boxes: DVD/VCR Code: NOTE: When ba tteries need repla cement, the remote control w ill stop opera ting. 5. For the first device you want in the power-on sequence, press its device key (e. g. , CBL/SAT) once. Repeat step 3 up to two more times to add desired devices to the power-on sequence (e. g. , DVD/VCR and TV). To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. CHECKING THE CODES If you have set up the remote control using the Searching For Your Code procedure as above, you may need to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV: 1. Press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. Operating The Master Power Macro 1. After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on (or off) your devices. NOTE: When POWER is pressed for less than 2 seconds, a power command will only be sent to the currently-selected device. This allows you to still individually power devices on or off. 2. To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e. g. , three blinks = 3) and write down the number in the leftmost box in the TV code boxes on page 8. NOTE: If a code digit is "0", the LED will not blink. Devices will turn on (or off) according to your programmed sequence. NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s). This action is normal. continued on next page. . . 9 10 WALRB3P manual booklet 5/2/06 3:13 PM Page 11 PROGRAMMING A MASTER POWER MACRO (cont'd) Clearing The Master Power Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Then press POWER once. PROGRAMMING FAVORITE CHANNEL SCAN In the CBL/SAT or TV mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when FAV is pressed (see Using Channel Scan on the previous page). NOTE: Favorite channels can only be programmed for one mode. After programming, if FAV is pressed while in another mode, the remote control will start scanning all channels instead (if applicable to the selected device). 1. On the remote control, press CBL/SAT or TV once. 3. Press and hold SET until the LED blinks twice, then release SET. The Master Power Macro is now cleared. 2. 3. Press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. RE-ASSIGNING DEVICE KEYS The One For All 3 Device Universal Remote Control can be set to control a DVD player and a VCR (or a PVR) or a second DVD player by re-assigning the unused CBL/SAT key as follows: 1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. 4. Use the keypad to enter a favorite channel number (e. g. , 031). [. . . ] This warranty gives you specific legal rights and you may also have other rights which vary from state to state. To obtain warranty service for a defective product, please return the product, preferably in the original carton, along with your purchase receipt, to the store of original purchase for the first 90 days. A note detailing the complaint would be helpful. The store, at its option, will replace or repair this product if found to be defective. If the unit has been purchased more than 90 days ago, please return it to CT Global Inc. [. . . ]