User manual UNIVERSAL REMOTE CONTROL UR5U-9000L SPECS SHEET

[. . . ] STEP2 Press the [COMPONENT] button (TV, AUD, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote toward the Component and press the [CH ] or [CH ] button one step at a time or keep it pressed. The remote will emit a series of ON/OFF commands. [. . . ] Now, program the rest of your Components by repeating STEPS 1-5. *Note : If the Pre-Programmed Method did not work, or if the Code Tables do not list your Component brand, use the Auto-Search Method as explained in Section C. If you wish to store the TV channel control in TV mode, use the following steps. STEP1 Press the [TV] button and the [OK/SEL] button simultaneously for 3 seconds. The [TV] Component LED will turn on for 30 seconds. The Component LED will blink twice to confirm the programming. To return to original state: If you wish to restore the CABLE channel control in TV mode, repeat the above steps but press [CBL] in STEP3 . Digit Code Programming Method - Section B). Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre-Programmed Method. D. Finding a Component Button's Setup Code Number If you used the Auto-Search Method to program a Component, you may not know what the correct code number is. Here is a way for you to identify the code number, so you can record it for future reference. STEP1 Press the [COMPONENT] button (TV, AUD, DVD or AUX) you want to verify and the [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds. STEP2 Press the [INFO] button and count the number of times the Component LED light blinks. This number indicates the first digit of the code, followed by the second and third, each separated by a one second pause when the LED will turn off. *Note :10 blinks represents the number zero. Example : One blink, (pause), eight blinks, (pause) and three blinks, indicates code number 183. Digit Code Programming Method Section B). If any of the functions do not work as they should, you need to find a new code. STEP5 Once you have found the correct 3-digit code, save it by pressing the [AUX] button one more time. The Component LED light will blink twice to confirm the code was stored. Now when you press the AUX button, all the buttons will work with that 5th Component. H. Programming Volume Control Volume and Mute control are factory-programmed to automatically transfer to the respective Component mode you select, as follows: CBL :CBL DVD :TV T V : TV AUD : AUD AUX : AUX If your remote model has custom-programmable Macro buttons available, they can be programmed to act as a 'Macro' or Favorite Channel button in CABLE mode. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can be accessed with one button press. STEP1 Press the [CBL] button to select the CBL mode. [. . . ] (Code Tables are on the backside of this Instruction Sheet. ) The Auto-Search Method scans through all the codes in the remote control, one at a time. When you are in setup mode, a component LED will light for 30 seconds. If you do not press a button within 30 seconds, the LED light will turn off and exit setup mode and you will need to start over. Universal Remote Control, Inc. www. universalremote. com OCE-0081A Rev 01 (11/13/09) However, you can program the volume controls (Volume Up, Volume Down and When the batteries are low and need to be Mute) from one Component to operate in replaced with fresh batteries, the Component LED lights will blink 2 times in sequence another Component. whenever a [POWER] button is pressed to If you wish to store the TV volume control in turn on equipment. Memory Lock System STEP1 Press the [CBL] button and the [OK/SEL] button simultaneously for This remote control is designed to retain pro3 seconds. [. . . ]