User manual US ELECTRONICS ENT-8000

[. . . ] Place the batteries in the compartment in positions matching the picture below. Replace the battery compartment cover. TRANSPORT KEYS perform standard functions for video recording for VCRs and DVD players and controls VOD functions in cable mode if the service is available displays a list of programs that you have recorded allowing you to select for viewing ! © 2003 US Electronics, LLC All rights reserved Part Number USE 18257, version 1. 0 05202003 IMPORTANT NOTE Use only new AA Alkaline batteries to insure consistent operation The Enterprise remote control is already programmed with the code for your Scientific-Atlanta© Cable Converter. The following sections will help you program your remote to control your other entertainment components. 5 3 Test the code by trying various functions. If the primary function keys fail to respond SMART SCANTM AUTOMATIC PROGRAMMING TM satisfactorily try the next code listed for the manufacturer. [. . . ] (TV or AUD) After you release the key, the CBL key will flash three times and turn off. To return volume control to the default state: 1 Press and hold the CBL device key until all the device keys begin to flash. The CBL key will continue to flash. 5 Press and release the POWER key. The device key will stop flashing and remain on. 6 Point the remote control at the component. 7 Press and hold the UP ARROW key until the component turns off. While holding the UP ARROW key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the component, press the DOWN ARROW key to return to the previous code. 2 Press and release the VOLUME UP key. The CBL device key will stop flashing and stay on. Press and release the VOLUME DOWN key, and then press and release the OK key. After you release the OK key, the CBL device key will flash three times and turn off. 8 Master Power Control 8 When the device turns off, you have found a candidate code. Press the POWER key to turn device back on. Test various functions using the remote control to determine if this code will work. If primary functions do not work, make sure the device is still on then resume Smart ScanTM by pressing the UP ARROW key to find another device code. The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the power button. The following steps describe how to program the Master Power Control function: 1 Press and hold the CBL device key until all the device keys begin to flash. The CBL key will continue to flash. 2 Press and release the POWER key. 9 Once you have found a satisfactory code, press SELECT to lock the code. The device key will then flash three times. Go to section 10 to recall and record your device codes. [. . . ] The Enterprise comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate Channel Lock: Audio Receiver Codes 4185 4020 · 4033 · 4103 · 4104 4149 · 4150 · 4151 · 4152 · 4173 Akai 4075 · 4119 Bose 4020 · 4211 Carver 4022 · 4083 · 4091 4093 · 4147 Casio 4021 · 4170 Cinema Sound 4036 Citation 4052 · 4212 Clarion 4059 Curtis Mathes 4021 Denon 4036 · 4106 · 4107 · 4108 4109 · 4110 Fisher 4083 · 4087 · 4147 · 4158 Garrard 4075 Harman Kardon 4052 · 4113 4160 · 4212 Hitachi 4110 JBL 4078 · 4161 JC Penney 4021 · 4170 JVC 4041 · 4043 · 4044 · 4079 1 Press and hold the CBL device key until all the device keys begin to flash (approximately 3 seconds). The CBL device key will flash three times to confirm the procedure. Repeat these steps to reactivate Channel Lock. 2 3 4 10 Recalling A Device Code TV/DVD & TV/VCR COMBO CODES NOTE: Certain combo boxes (single devices that have more than one component built in) must be treated as separate discrete devices. [. . . ]