User manual US ELECTRONICS ENT-VGER

[. . . ] Place the batteries in the compartment in positions matching the picture below. Replace the battery compartment cover. MUTE turns volume on and off TRANSPORT KEYS perform standard functions for video recording for VCRs and DVD players and controls VOD functions in cable mode if the service is available STOP PLAY FF REC PAUSE ! © 2003 US Electronics, LLC All rights reserved Part Number USE 18256, version 1. 0 05202003 IMPORTANT NOTE Use only new AA Alkaline batteries to insure consistent operation The Enterprise remote control is already programmed with the code for your Pioneer© Cable Converter. The following sections will help you program your remote to control your other entertainment components. 5 3 Test the code by trying various functions. If the primary function keys fail to respond SMART SCANTM AUTOMATIC PROGRAMMING TM satisfactorily try the next code listed for the manufacturer. [. . . ] (TV or AUD) After you release the key, the CBL key will flash three times and turn off. To return volume control to the default state: 1 Press and hold the CBL device key until all the device keys begin to flash. The CBL key will continue to flash. 5 Press and release the POWER key. The device key will stop flashing and remain on. 6 Point the remote control at the component. 7 Press and hold the UP ARROW key until the component turns off. While holding the UP ARROW key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the component, press the DOWN ARROW key to return to the previous code. 2 Press and release the VOLUME UP key. The CBL device key will stop flashing and stay on. Press and release the VOLUME DOWN key, and then press and release the OK key. After you release the OK key, the CBL device key will flash three times and turn off. 8 Master Power Control 8 When the device turns off, you have found a candidate code. Press the POWER key to turn device back on. Test various functions using the remote control to determine if this code will work. If primary functions do not work, make sure the device is still on then resume Smart ScanTM by pressing the UP ARROW key to find another device code. The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the power button. The following steps describe how to program the Master Power Control function: 1 Press and hold the CBL device key until all the device keys begin to flash. The CBL key will continue to flash. 2 Press and release the POWER key. 9 Once you have found a satisfactory code, press SELECT to lock the code. The device key will then flash three times. Go to section 10 to recall and record your device codes. When all the codes have been attempted the device button will flash rapidly. 3 Individually press and release each device key corresponding to the components you wish to be controlled by Master Power. NOTE: If no keys are pressed in this step, no change will occur in Master Power programming. 4 Press and release the POWER key. [. . . ] If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate Channel Lock: Audio Receiver Codes 4185 4020 · 4033 · 4103 · 4104 4149 · 4150 · 4151 · 4152 · 4173 Akai 4075 · 4119 Bose 4020 · 4211 Carver 4022 · 4083 · 4091 4093 · 4147 Casio 4021 · 4170 Cinema Sound 4036 Citation 4052 · 4212 Clarion 4059 Curtis Mathes 4021 Denon 4036 · 4106 · 4107 · 4108 4109 · 4110 Fisher 4083 · 4087 · 4147 · 4158 Garrard 4075 Harman Kardon 4052 · 4113 4160 · 4212 Hitachi 4110 JBL 4078 · 4161 JC Penney 4021 · 4170 JVC 4041 · 4043 · 4044 · 4079 1 Press and hold the CBL device key until all the device keys begin to flash (approximately 3 seconds). The CBL device key will flash three times to confirm the procedure. Repeat these steps to reactivate Channel Lock. 2 3 4 10 Recalling A Device Code TV/DVD & TV/VCR COMBO CODES NOTE: Certain combo boxes (single devices that have more than one component built in) must be treated as separate discrete devices. If you are not able to control your combo box with the codes listed below please try to code setup each device (TV, VCR, DVD) separately using the codes found in the corresponding sections. Aiwa Audio Dynamics Broksonic Curtis Mathes DBX Daewoo Electrohome Emerson Funai General Electric Goldstar Harman Kardon Hitachi JC Penney JVC Kenwood LXI MGA MTC Magnavox Marantz 5251 5238 5219 · 5226 · 5228 5241 · 5251 5238 5247 · 5250 · 5252 5240 5219 · 5223 · 5226 · 5251 5252 · 5253 5251 5233 · 5241 · 5248 5223 · 5230 · 5238 5238 5241 · 5251 5223 · 5238 · 5241 · 5242 5235 · 5238 5235 · 5251 5223 · 5251 5240 5251 5236 · 5237 · 5241 · 5251 5237 · 5238 Marta Memorex Mitsubishi Multitech Optimus Orion Panasonic Philco Philips Pioneer Proscan Pulsar Quasar RCA Radio Shack Realistic Runco Samsung Sansui Sanyo 5223 5223 · 5242 · 5244 5248 · 5251 5239 · 5240 5251 5242 5219 · 5226 5241 · 5242 · 5255 5236 · 5237 · 5251 5223 · 5236 · 5237 · 5251 5235 5233 5248 5241 · 5242 5233 · 5241 · 5251 5230 · 5242 · 5251 5223 · 5251 5243 5221 · 5229 · 5244 5246 · 5247 5219 · 5235 · 5251 5244 Scott Sears Signature Sony Soundesign Sylvania Symphonic Tandy Teac Technics Teknika Toshiba Totevision Vector Research Victor Video Concepts Wards Yamaha Zenith 5247 5223 · 5251 5251 5232 5251 5237 · 5240 · 5251 5251 5251 5251 5242 5223 · 5251 5228 · 5240 · 5247 5223 5238 5235 5238 · 5251 5251 5238 · 5251 5219 · 5223 · 5235 · 5248 5249 · 5251 Use the following steps to read the code set for a device. [. . . ]