User manual US ROBOTICS 3CP3453

[. . . ] Courier V. Everything Internal Modem: Getting Started FINAL 4/96 p/n 1. 024. 493 ©1996 U. S. Skokie, IL 60076-2999 All Rights Reserved U. S. Robotics logo are registered trademarks of U. S. V. Fast Class and V. FC are trademarks of Rockwell International. [. . . ] You should see a message indicating that a new connection was created successfully. Click Finish. Communicating with the Courier 3-5 13 From the Dial-Up Networking window, put the cursor over your new icon and click the right mouse button. Select Properties from the menu that appears. 14 Click Server Type. . . , and then deselect Log on to Network, NetBEUI, and IPX/SPX Compatible. 15 Select OK, then OK. Double-click on your new connection icon to connect! 3-6 Courier V. Everything Internal Modems: Getting Started Windows 3. x First, try testing the Courier by following the steps below. Use any communications software package for this test. For example, Windows includes Terminal, a minimally equipped communications program. Because Terminal supports serial port rates of up to only 19200, Quick Link II Fax is used in this example. 1 2 Install and then start Quick Link. If you are using a computer with a serial port that cannot support high speeds, choose 19200. Then click OK. 3 Click Setup | Modem Setup. . . Select the COM Port that the Courier is using (the one you set using the jumpers in Chapter 2). In the terminal window, type AT <Enter>. The Courier should respond OK. 4 Communicating with the Courier 3-7 If you don't get an OK response, refer to Chapter 16, Troubleshooting, in the Courier Modems Command Reference manual. 5 Dial the U. S. For example, ATDT18479825092 <Enter> dials the U. S. NOTE: If you need to dial 9 to get an outside line, dial as in this example: ATDT9, 18479825092 <Enter>. If you want to disable call waiting for this call, in most areas, dial *70 before you dial the phone number, for example, ATDT*70, 18479825092 <Enter>. The following screens are what you should see when you dial the BBS. atdt9825092 CONNECT 31200/ARQ/V34/LAPM/V42BIS CONNECT 31200/ARQ/V34/LAPM/V42BIS CONNECT 115200 / 02-27-96 (12:52:21) (Error Correcting Modem Detected) USR Support BBS - ComServer 486 PCBoard (R) v15. 22/100 - Node 11 Testing your system capability. . . Success! 3-8 Courier V. Everything Internal Modems: Getting Started For other Windows software packages, see Chapter 4, Setups for Common Windows Software Packages. For instructions about how to set up your Windows communications software package, call our fax-on-demand service (at 800-762-6163 or 847-676-1598) or our BBS (at 847-9825092). Request document 10000 for a list of our technical support documents. Windows NT Determining COM Port, IRQ, and I/O Address Settings Use WinMSD to determine which COM ports, IRQs, and I/O base addresses are free. Bear in mind that you can change the settings in Control Panel | Ports | Advanced only if you have logged in to NT as administrator. As a Client If you want only to dial out using the Courier, Windows NT works very much like Windows 3. x. Windows NT ships with a built-in Terminal program that can support speeds of up to 115. 2 Kbps. Additionally, Windows NT includes a Remote Access Dialer, but it is not installed by default. You can install Quick Link II in Windows NT but you may experience problems with fax operations. As a Server Here's how to set up Windows NT Remote Access Service (RAS) to recognize the Courier. [. . . ] Robotics at the address on page 16-8 in the Courier Modems Command Reference. IMPORTANT: If you ship your unit, pack it securely, be sure your SRO number is visible on the outside of the package, and ship it charges prepaid and insured. B-2 Courier V. Everything Internal Modem: Getting Started Notices FCC Registration FCC15: CJE-0269 FCC 68: CJEUSA-73130-FA-E Connecting to the Telephone Company's Lines The telephone company may request the telephone number(s) to which the Courier is connected and the FCC information printed above. If the Courier is malfunctioning, it may affect the telephone lines. In this case, disconnect the Courier until the source of the difficulty is traced. FCC Notice: Radio and Television Interference This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ]